54 |
P a g e
T-POST INSTALLATION ALIGNMENT BLOCK WITH
4-SIDED FRAME
1.
ATTACH T-POST BLOCKS TO FRAME
•
Stack two T Post Alignment Blocks, both with the tabs facing down.
•
Lay out the top frame so that the light block is facing up.
•
Two holes have been pre-drilled diagonally in the face of the top frame at each
T Post location.
•
Position the stacked blocks on the light block portion of the frame so that the
holes in the block align with the pre-drilled holes in the frame. (The tabs will hang
off the edge of the light block.)
•
Using (2) #6 x 44mm T Post block screws, attach the blocks to the frame. Do not
completely tighten the screws down, only make them snug. This will allow some
side-to-side adjustment of the T Post.
•
Repeat the above steps for the top frame.
2.
ASSEMBLE FRAME AND T-POST
•
Insert the corner keys into the top frame.
•
Attach the left side frame to the top frame.
•
Attach the right side frame to the top frame.
•
Attach T Post to the top frame by sliding the T-Post over the blocks on the bottom
frame.
•
Attach the top frame. Make sure the corner keys in each end of the top frame
align with the corner key cavities in the side frames. At the same time make sure
the T Post is positioned on the blocks attached to the top frame.
3.
INSTALL THE SHUTTER
•
Follow standard instructions for installing the frame.
•
Test the fit and position of the panels to determine the location of the T Post.
•
Mark the position of the T Post on the frame with a pencil.
•
Remove the panels
4.
ALIGN T-POST AND SECURE
•
With the bottom of the T Post in the desired position, drive a #8 x 38mm
installation screw horizontally through the hole in the end of the T Post.
•
The screw will then pass between the (2) T-Post Blocks, thus locking the T Post into
position.
•
Repeat for the top of the T Post and cap installation holes with button covers.
Summary of Contents for Eclipse Shutters
