WeatherBug UM24 System Installation, Operation And Maintenance Manual Download Page 13 | Manualshive

Page: 13 / 29

background image

HD MotionCam

Installation Manual

EN.PM.UM24 20160211

-13-

Page 13 of 29

Viewing Live Video and Captured Images

Live Video

In order to obtain live video from the camera, acquire the internal IP address of
the camera. To do this, download the finder tool from the internet. Open an
Internet Explorer web browser on a computer connected to the same subnet as the
camera.

THE HD MOTIONCAM ABSOLUTELY MUST BE CONNECTED

TO THE SAME SUBNET AS THE COMPUTER USED TO AQUIRE THE
INTERNAL IP ADDRESS OF THE CAMERA.

1.

To begin, visit

http://download.aws.com

. Click on the link that says “HD

MotionCam Finder Tool”

«
...
11
12
13
14
15
...
»

Summary of Contents for UM24






























Reviews:

No comments

Related manuals for UM24

Brand: Panasonic Pages: 48

Brand: Ecco Pages: 2

Brand: Waters Pages: 2

Brand: Y-cam Pages: 8

Brand: Axis Pages: 2

Brand: Axis Pages: 2

IQeye Sentinel Series

Brand: Iqinvision Pages: 15

treeMOTION S.light USCA

Brand: TEUFELBERGER Pages: 152

Brand: Smartwares Pages: 2

Brand: Uniden Pages: 68

Brand: Guardian Pages: 2

ThermoXplorer Pro

Brand: LaserLiner Pages: 121

Brand: Dahua Pages: 25

Brand: SICK Pages: 112

Brand: nedis Pages: 37

Brand: i-PRO Pages: 26

SpectrAlert S900RLFIRE

Brand: System Sensor Pages: 2

Brand: HiLook Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands