REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
Description
A sewage system consists of a pump,
control switch, and a basin for use in
applications where less than six toilets
(units) are discharged into the basin.
The system is generally controlled by a
float switch with a plug-in-plug which
accepts the pump plug and in turn
plugs into a 120 volt outlet.
The float switch is a wide angle
differential switch that rises with the
liquid level and turns the pump on. As
the liquid level decreases the float
lowers and turns the pump off. The
CSECAP40 and CSECAP50 are provided
with a solid-state electronic “Switch-
Genius” water level control. When
Operating Instructions and Parts Manual
CSECAP40, CSECAP50, CSE50T
330502-001 11/07
water is detected, the pump will start
automatically. This pump is intended
for use in domestic sewage lift stations.
It is suitable for pumping sewage,
effluent, wastewater, groundwater and
other nonexplosive, noncorrosive
liquids with up to 2 inch solids.
Unpacking
Inspect this unit before it is used.
Occasionally, products are damaged
during shipment. If the pump or
components are damaged, return the
unit to the place of purchase for
replacement. Failure to do so could
result in serious injury or death.
Safety Guidelines
This manual contains information that
is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols.
Danger
indicates
an imminently hazardous situation
which, if not avoided, will result in
death or serious injury.
Warning
indicates
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
Caution
indicates
a potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
Notice
indicates
important information, that if not
followed, may cause damage to
equipment.
SAVE THESE INSTRUCTIONS!
© 2007 Wayne Water Systems
Specifications
CSECAP40
CSE50T
CSECAP50
Power supply requirements
120V, 60 hz
120V, 60 hz
Circuit requirements
15 amps (min)
15 amps (min)
Motor duty
Intermittent
Intermittent
Motor
120V, 1 Phase
120V, 1 Phase
Horsepower 1/2
4/10 (CSECAP40)
1/2 (CSECAP50)
Motor full load
12.0
8.7
Liquid temperature range
40°F to 120°F
40°F to 120°F
Max. operating position
45
o
from vertical
45
o
from vertical
Dimensions
14 inches x 12inches 14 inches x 12inches
Intake
2 inches
2 inches
Discharge
2 inch NPT female
2 inch NPT female
Cut-in level (factory set)
19 inches
11 inches
Cut-out level (factory set)
9 inches
3 inches
Differential
10 inches
7 inches
Switch
90
o
wide angle
“Switch-Genius”
mechanical
capacitive
tether switch
water sensor
Power cord
16 gauge
16 gauge
3 Conductor w/plug
3 Conductor w/plug
Construction
Motor body material .......................Cold rolled steel
Motor housing .................................Cast iron
Volute ...............................................Cast iron
Impeller.............................................Glass reinforced PBT
Seal plate ..........................................Cast Iron
Shaft seal ..........................................Mechanical
GALLONS PER MINUTE AT TOTAL HEAD IN FEET
Model
5'
10'
15'
CSECAP40
90
62
23
CSECAP50, CSE50T
113
90
33
Performance
Sewage
Pump
For parts, product & service information
visit
www.waynepumps.com
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.