background image

Limited Warranty

Models 8000, 8100, 8200

Wayne Dalton, a division of Overhead Door Corporation ("Seller") warrants to the original purchaser of the Models 8000, 8100, 8200 (“Product”), subject to all of 

the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, 

measured from the date of installation:

TEN (10) YEARS

 from the date of installation against:

• The Product becoming inoperable due to rust-through of the steel skin from the core of the Product section, due to cracking, splitting, or other deterioration of 

the steel skin, or due to structural failure caused by separation or degradation of the foam insulation.

• Peeling of the original paint as a result of a defect in the original paint or in the application of the original paint coating.

TEN (10) YEARS

 on Product hardware and tracks (except springs).

ONE (1) YEAR

 on all other component and parts.

Seller’s obligation under this warranty is specifically limited to repairing or replacing, at its option, any part which is determined by Seller to be defective during 

the applicable warranty period. Any labor charges are excluded and will be the responsibility of the purchaser.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is made to the original purchaser 

of the Product only, and is not transferable or assignable. This warranty applies only to Product installed in a residential or other non-commercial application. It does not 

cover any Product installed in commercial or industrial building applications.  This warranty does not apply to any unauthorized alteration or repair of the Product, or to 

any Product or component which has been damaged or deteriorated due to misuse, neglect, accident, failure to provide necessary maintenance, normal wear and tear, 

acts of God, or any other cause beyond the reasonable control of Seller or as a result of having been exposed to toxic or abrasive environments, including blowing sand, 

salt water, salt spray and toxic chemicals and fumes.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 

FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE APPLICABLE WARRANTY PERIOD REFLECTED ABOVE. NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, 

WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation 

may not apply to you.

IN NO EVENT SHALL SELLER BE RESPONSIBLE FOR, OR LIABLE TO ANYONE FOR, SPECIAL, INDIRECT, COLLATERAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES, even if Seller has been advised of the possibility of such damages. Such excluded damages include, but are not limited to, loss of use, cost of any substitute 

product, or other similar indirect financial loss.  Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or 

exclusion may not apply to you.

Claims under this warranty must be made promptly after discovery, within the applicable warranty period, and in writing to the authorized distributor or installer 

whose name and address appear below. The purchaser must allow Seller a reasonable opportunity to inspect any Product claimed to be defective prior to removal or 

any alteration of its condition. Proof of the purchase and/or installation date, and identification as the original purchaser, may be required. There are no established 

informal dispute resolution procedures of the type described in the Magnuson-Moss Warranty Act.

• SELLER:                          _______________________________________________________________________

• SELLER’S ADDRESS:  

_______________________________________________________________________

 

  _______________________________________________________________________

20

Warranty

Summary of Contents for 8000 Series























Reviews: