background image

Page 10

 

 

 
 
 
 

 

 

 

 

 
 
 

 
 

 

Connect Yellow Tube from TANK Port on RO Module to the Tank

Position tank in desired location.  Stand it upright or lay it  on its 
side (using the black plastic stand).  Measure the yellow tube from 
the RO module port  marked TANK  over to the tank and cut it to 
desired length.

Insert the white 1/4” tube through tank valve compression nut.  
Place 1/4” plastic insert in tubing.  Push tubing into valve.  Hand 
tighten the compression nut securely, and add 1/4 turn with a 
wrench.

Step 22

 

 

 

 

 

 

 

 

Step 19

Step 21

Step 20

                        Adapta Valve 

Remove a brass nut, plastic  sleeve and brass insert from the parts 
bag.  Place nut on  the tube fi rst, then the sleeve (Small taper end 
of sleeve must point to the end of tube) and then insert the brass 
insert into the end of the tube. 

Insert the black tube into the ¼” opening on the adapta valve until 
it stops.  Slide  nut and sleeve down and thread onto the male pipe 
threads.  Use a ½” wrench to securely tighten.  Run the tube to the 
inlet on the side label IN of the RO system.  Leave enough tube so 
it is not kinked and cut the tube to desired length.

Connect BlackTube from Adapta Valve to IN Port on RO module

Note:  The DRAIN & TANK 
connections are underneath 
the bracket.  See page 12

DRAIN

FAUCET

TANK

Yellow Tube Connection

Determine if you have an Airgap or Non Airgap faucet and continue 
the following steps to install tubing correctly. 

Note:

IN

Summary of Contents for WQT4RO11-50




















Reviews: