background image

Page 7

 

 

 
 
 
 

 

 

 

 

 
 
 

 
 

 

Adapta Valve Installation   

Locate the cold water supply under the sink.

Reverse Osmosis Module Mounting

Step 13

Determine best location for the RO module to be mounted to allow  
for future system maintenance.  The parts bag has 3 self tapping 
screws.  Using a Phillips screwdriver, screw them into the cabinet 
wall 13 5/8” apart and 16” from the bottom of the cabinet.  After 
bracket is attached to the wall take the last screw and screw in where 
the hole is located.  This will be used so that the bracket is in tact and 
not moving around when doing maintenance on unit.

Step 10

Step 12

 Attach adapta valve as illustrated in the three photos above, choosing the confi guration that 
fi ts your plumbing.  (When attaching the adapta valve to straight pipe threads, use Tefl on 
tape on the threads).   The white tube from  inlet side of RO module will be cut to length and 
attached later in the installation.

Do not cut any RO system tubes at this time.

Note:

Caution: Water supply line to the system must be from the cold water supply line only.  Hot 

water will severely damage your system.

Confi guration for 3/8”  
compression fi ttings  

Confi guration for 1/2”  
compression fi ttings  

Hot

Supply

Cold

Supply

 

Turn off the cold water supply to the faucet by turning the angle stop valve completely off.

Step 11

Summary of Contents for WQT4RO11-50




















Reviews: