background image

11

IOM-T-482

  2125 

 

© 2021 Watts

Each thermostat and setpoint control uses the following 
format for addressing: 

Port:Bus:Thermostat Device

The snow melting control does not reports its address to 
the 482. The Bus and Thermostat Device are visible on 
the thermostat and setpoint control’s LCD display. This is 
documented as the ‘tekmarNet Address’ in the thermostat 
data brochure.

Port Number

The leading digit is the Port number. This determined by 
the wiring connection that the thermostat is wired to on 
the 482.

482 tN4 Bus 0 or b = 0

482 tN4 Bus 3 = 3

482 tN4 Bus 1 = 1

482 tN4 Bus 4 = 4

482 tN4 Bus 2 = 2

Bus Number

The second digit is the thermostat bus number. The bus 
number is pre-determined by the wiring of the thermostat 
to a boiler or mixing reset control water temperature bus.
In the event that no reset control is installed, the bus  
number is 0.

The 406 tN4 bus numbering is dependent on the 
WaterTemp and the Zone settings when configuring  
the control.

WATERTEMP

ZONES

TANK BUS

MIX BUS

BOILER BUS

T

1

T + M

1

2

T + B

1

2

T + MB

Mix

1

*

3

T + MB

Boil

1

2

*

*When the 406 is configured in this manner, thermostats on 
this bus are unable to communicate to the Gateway 482.

Thermostat Device Number

The third and fourth digits indicate the thermostat device 
number. The thermostat device number is a two digit 
number that ranges from 01 to 24 and can be determined 
from the thermostat address. To determine the thermostat 
address, please consult the data brochure for the  
appropriate thermostat.

Example 1

A thermostat with bus and thermostat device number of 
b:01 is wired to a model 400 controller boiler bus and in 
turn is wired to the 482 on port 0. This address is 0101.

Example 2

A thermostat with bus and thermostat device number of 
b:24 is wired to a model 423 controller boiler bus and in 
turn is wired to the 482 on port 0. This address is 0424.

Example 3

A group of thermostats are wired together to create a 
stand-alone network. A thermostat with thermostat device  
number 15 is wired to the 482 on port 0. This address  
is 0015.

CONTROL

BUS

BUS #

274

Boiler

1

275

Boiler

1

284

b

1

284

1

2

284

2

3

284

3

4

400

Boiler

1

401

Boiler 

1

402

Mix

1

402

Boiler

2

403

Mix

1

CONTROL

BUS

BUS #

403

Boiler 

2

420

Boiler

1

421

Mix

1

422

Mix1

1

422

Boiler 

2

422

Mix2

2

423

Bus1

1

423

Bus2

2

423

Bus3

3

423

Boiler

4

THERMOSTAT (HEAT ONLY)

THERMOSTAT (HEAT-COOL)

SETPOINT CONTROLS

SNOW MELT

COMMAND

532

552

553

554

557

161

162

654

670

671

Room temperature

Floor temperature***

Mode

Heat setpoint

Cool setpoint

Slab setpoint*

Setpoint control setpoint

Fan

Relative humidity%

Maximum humidity setpoint

Minimum humidity setpoint

Outdoor temperature**

Melt/storm/setpoint enable

* Not supported by some home automation drivers
** Requires an outdoor sensor to be connected to a thermostat, snow melt or boiler control
*** Floor temperature available when a floor sensor is installed to an auxiliary sensor input

Home Automation Commands

Thermostat Addressing 

Summary of Contents for TekmarNet 4













Reviews: