background image

IOM-UPGRADEKIT-SentryPlusAlert

Installation, Operation, and 

Maintenance Manual

SentryPlus™ Alert

Universal Upgrade Kit 

WARNING

!

Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information 

can result in death, serious personal injury, property 

damage, or damage to the equipment.
Keep this Manual for future reference.

Table of Contents

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Understanding Safety Information  . . . . . . . . . . . . . . . . . . . . 2

Description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
List of Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Required Tools and Materials for Installation  . . . . . . . . . . . . . . 2
Installation and Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

 ISolenoid  Operation 

(For Existing LFF113RFP Installations Only) . . . . . . . . . . . . . 3
Installing the Flow Sensor (Backflow Upgrade Kit Only) . . . . 3
Wiring/Retrofitting the junction box  . . . . . . . . . . . . . . . . . . . 4
Installing the Wireless Node . . . . . . . . . . . . . . . . . . . . . . . . . 6

Registering Your Device and Alert Configuration  . . . . . . . . . . . 7
Start-up Instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Summary of Contents for SentryPlus 113RFP









Reviews: