background image

 

 

 

@2022 PVI 

    

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: If the information in these instructions is not 
followed exactly, a fire or explosion may result causing 
property damage, personal injury or death. 

Do not store or use gasoline or other flammable vapors 
and liquids in the vicinity of this or any other appliance. 

WHAT TO DO IF YOU SMELL GAS 

 

Do not try to light any appliance. 

 

Do not touch any electrical switch; do not use any 
phone in your building. 

 

Immediately call your gas supplier from a 
neighbor's phone. Follow the gas supplier's 
instructions. 

 

If you cannot reach your gas supplier, call the fire 
department. 

Installation and service must be performed by a qualified 
installer, service agency or the gas supplier. 

OMM-0153_A     

•    8/25/2022 

Disclaimer 

The information contained in this manual is subject to change without 
notice from PVI Industries, LLC. PVI makes no warranty of any kind 
with respect to this material, including, but not limited to, implied 
warranties of merchantability and fitness for a particular application. 
PVI is not liable for errors appearing in this manual, not for incidental 
or consequential damages occurring in connection with the 
furnishing, performance, or use of these materials. 

CENTURION Water Heaters  

with Edge

®

 [ii] Controller

 

Natural Gas Modulating & Condensing  
Water Heater Model CEN2000 

Installation, Operation and Maintenance Manual 

Summary of Contents for PVi CENTURION




































































































































Reviews: