background image

4          IOM-A-ACV-986_686   2115 

EDP# 1917094 

© 2021 Watts

IOM-A-ACV-986_686   2115 

EDP# 1917094 

© 2021 Watts         5

needle valve regulates fluid pressure into the main valve cover 
chamber, controlling the valve closing speed.

If valve closing is too slow, turn the adjustment screw OUT, coun-
terclockwise, increasing the rate of closing.

STEP 9

At valve closure booster pump will stop. Adjust limit switch collar 
to final position to ensure positive actuation of limit switch electri-
cal contact, if necessary, by sliding up/down to location. (See 
Figure 3).

STEP 5

Energize the solenoid at pump start to open the main valve, 
checking that the main valve opens. Air is vented through the 
loosened fitting. Tighten the fitting when liquid begins to vent.

STEP 6

Opening Speed Flow Control Adjustment: The Opening speed 
needle valve restricts flow into the cover and restricted flow out of 
the cover of the main valve. 

If valve opening is too slow, turn the adjustment screw OUT, 
counterclockwise, increasing the rate of opening (See Figure 2B).

 If valve opening is too quick, turn the adjustment screw IN, 
clockwise, decreasing the rate of opening (See Figure 2A).

STEP 7

De-energize solenoid to check that the main valve closes.

STEP 8

Closing Speed Needle Valve Adjustment: The closing speed 

Counterclockwise to INCREASE 

the rate of opening

Clockwise to DECREASE 

rate of opening

2A

2B

Figure 2 

Flow Control

Figure 3 

Limit Switch in Closed Position

Summary of Contents for Ames 686GD













Reviews: