background image

 

Heating and Hot Water Solutions 

AERCO International, Inc.  •  100 Oritani Drive • Blauvelt, NY 10913 

USA: T: (845) 580-

8000 • Toll Free: (800) 526-0288 • AERCO.com 

Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST 

© 2021 AERCO 

   

 

 

 

 

 

 

 

 

 

       

 

 

 

 

Installation, Operation & Maintenance Manual 

SmartPlate

®

 EV 

High Pressure Domestic  
Hot Water Heaters

 

Five Double Wall Models

  SPDW-EV30 

  SPDW-EV40 

  SPDW-EV60 

 

SPDW-EV90 

  SPDW-EV140 

 

OMM-0147_C    

•   SP-102     •     3/2/2021 

Disclaimer 

The information contained in this manual is subject to change without notice 
from AERCO International, Inc. AERCO makes no warranty of any kind with 
respect to this material, including, but not limited to, implied warranties of 
merchantability and fitness for a particular application. AERCO International is 
not liable for errors appearing in this manual, not for incidental or 
consequential damages occurring in connection with the furnishing, 
performance, or use of these materials. 

 

Summary of Contents for Aerco SmartPlate EV









































































Reviews: