background image

 

 SECTION  2: INSTALLATION  

 

   

 

 2.12  Combustion Air 

Air supply is a direct requirement of ANSI 223.1, NFPA-54, and local codes. These codes should be 
consulted before a permanent design is determined.  

The combustion air must be free of chlorine, halogenated hydrocarbons, and other chemicals that can 
become hazardous when used in gas-fired equipment. Common sources of these compounds are 
swimming pools, degreasing compounds, plastic processing, and refrigerants. Whenever the environment 
contains these types of chemicals, combustion air MUST be supplied from a clean area outdoors for the 
protection and longevity of the equipment and warranty validation. 

If combustion air is not supplied through air ducts, it must be supplied to the unit(s) through two 
permanent openings. These two openings must have a free area of 

not less than one square inch (6.5 

cm

2

) for each 4000 BTUs (1.17 kW) input

 for 

each unit

. The free area must take into account restrictions 

such as louvers and bird screens.  

2.12.1  Ducted Combustion Air 

For ducted combustion air installations, the air ductwork must be attached directly to the air inlet 
connection on the sheet metal enclosure. Consult the 

CFR Venting and Combustion Air Guide

, TAG-0105 

when designing combustion air ducting.   

When using the unit in a ducted combustion air configuration, the minimum diameter connection at the 
unit is 

8-inches

 

 2.13  CFR Pump Relay  

The CFR power panel includes a pump relay terminal block providing 120VAC with a maximum pilot duty 
of 3 amps. If the pump power requirement under all conditions is greater than 3 amps, use this relay to 
activate the pump through an intermediate relay with a higher power. 

 

Figure 2-16: Pump Relay Terminal Block (in Red Rectangle) 

The Pump Delay Timer feature allows pump to run for up to 30 minutes after the boiler has shut down 
and the demand is satisfied. To enable, go to 

Advanced Setup 

 Ancillary Devices 

 Relays

 and set the 

Pump Off Delay 

setting to the desired delays time

 

Summary of Contents for AERCO CFR 3000


























Reviews: