background image

 

 SECTION  2: INSTALLATION  

 

   

 

 

DO NOT make connections to terminals labeled 

NOT USED”.  Attempting to do so may damage equipment. 

 

 

Figure 2-12:  Terminal Block Terminal Strips 

 

2.10.1  I/O Board Connections 

The I/O board contains the terminal listed below, arranged on removable, named connector strips J3 
through J7 and J14, plus Molex connectors for unit harnesses.  The maximum gauge of wires connecting 
to the I/O board is 14. 

NOTE: 

To facilitate connections, these strips can be lifted off the I/O board. The entire strip is then remounted 

on the I/O board after all connections have been made.  If a connector strip is removed, it must be re-mounted 
in its original orientation (connecting wires arranged around the 

outside

 perimeter of the I/O board). 

 

Connector Strip J3 Terminals 

Pin #  Name 

Description 

 

Outside Temp + 
 
Outside Temp - 

Connections  to  Outside  Air  Temperature  (OAT)  sensor  (P/N 

61048

).  Used  on 

Manager and Backup Manager units. Required for the 

OUTDOOR RESET

 mode of 

operation. To enable this mode, 

go  to the Controller’s 

Main Menu 

 Advanced 

Setup 

    Unit 

    Application  Configuration

 

and  set

  SH  Operating  Mode 

to 

Outdoor Reset

, then configure the related parameters. 

Shield 

Connection to the shield from any cable. 

 

Supply  
 
Supply Header 

 

Connection to the Supply Header temperature sensor (2 wire sensor P/N 

24410

or

 

4 wire sensor

 

P/N

 61058

) for: 

 

Main Loop (in a Variable-Primary application)  

 

Secondary Loop (in a Primary-Secondary application)   

 

Loop 1 (in a Multi-application) 

Typically, used on Manager and Backup Manager units. 
For more information, refer to the 

CFR Boiler Application Guide

 (TAG-0107)  

 

Remote Analog In + 

Connection to the Analog Remote Signal, if Operating Mode = Remote Setpoint. 
Used on Manager and Backup Manager units. 

Remote Analog In 

 

SPARK MONITOR 
FROM SHELL 
HARNESS 63394-2 
 CONNECTOR J9 

I/O BOARD POWER 

HARNESS 63232  

CONNECTOR J24 

 

VALVE HARNESS 
INTERLOCK FROM SHELL 
HARNESS  63394-2  
J6 PINS 3 & 4 

40 PIN RIBBON I/O 

HARNESS 63220  

CONNECTOR J1 

30 PIN RIBBON I/O HARNESS 63221  
CONNECTOR J2 

Summary of Contents for AERCO CFR 3000


























Reviews: