background image

 
 
 

 

CHAPTER 2:  INSTALLATION 

PR2: 04/22/13                                                                                                                                      Page 

15

 of 

158

 

 

 
 

Benchmark 2.0LN Dual-Fuel Low NOx Boiler  

Operation and Maintenance Manual 

OMM-0052_0E 

GF-127

 

AERCO International, Inc. 

 100 Oritani Dr. 

  Blauvelt, NY 10913 

 Ph: 800-526-0288  

 

EXHAUST

MANIFOLD

1/2” NPT 

CONDENSATE 

DRAIN 

CONNECTION

HOUSE-

KEEPING

PAD

BOILER

RETURN

 

Figure 2-4: Condensate Drain Connection Location 

Exhaust Manifold Condensate Drain 

2.6.1  

NOTE 

There are two slightly different types of condensate traps 
that may be used in your configuration; an older style 
without built-in adapter, and a newer style with a built-in 
adapter (see Figure 2-5). Installation is the same (1/4” 
threads are inside built-in adapter on newer style). 

A condensate drain trap (part no. 24060) is shipped loose and must be installed at the rear of 
the unit. The trap inlet and outlet contain tapped 3/4” NPT ports. The actual installation details 
for the condensate trap will depend on the available clearances, housekeeping pad 
height/dimensions and other prevailing conditions at the site. However, the following guidelines 
must be observed to ensure proper condensate trap operation: 

  The condensate trap inlet (Figure 2-5) must be level with, or lower than the exhaust manifold 

drain port. 

  The condensate trap must be supported to ensure that its base is level (horizontal). 

  The trap must be removable for routine maintenance. AERCO recommends that a union be 

utilized between the exhaust manifold condensate drain port and the trap inlet port. 

1.  While observing the above guidelines, connect the condensate trap inlet to the exhaust 

manifold drain connection using the appropriate piping components (nipples, reducers, 
elbows, etc.) for the boiler installation site. 

2.  At the condensate trap outlet, install a 3/4” NPT nipple.  

3.  Connect a length of 1” I.D polypropylene hose to the trap outlet and secure with a hose 

clamp. 

4.  Route the hose on the trap outlet to a nearby floor drain. 

If a floor drain is not available, a condensate pump can be used to remove the condensate to 
drain.  The maximum condensate flow rate is 20

 

GPH. The condensate drain trap, associated 

fittings and drain line must be removable for routine maintenance.  

Summary of Contents for AERCO Benchmark 2.0LN































































































































































Reviews: