background image

Page 23

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVALS:

Depending on incoming feed water conditions replacement time frame may vary.

Change Time  

Description 

 

6 months:  

Sediment Pre-filter;  Carbon Pre-filters   

 

12 months 

Final Carbon filter   

2 to 5 years  

R.O. Membrane 

This system has been tested according to NSF/ANSI 58 for reduction of the substances below.  The concentration of the indicated substances in 

water enter�

ed in 

NSF/ANSI 58.  This system has been tested for the treatment of water containing pentavalent arsenic (also known as As (V), As (+5), or arsenate) 

at concentrations of 0.30 mg/L or less.   This system reduces pentavalent arsenic, but may not remove other forms of arsenic.  This system is to 

be used on water supplies containing a detectable free chlorine residual at the system inlet or on water supplies that have been demonstrated to 

contain only pentavalent arsenic.  Treatment with chloramine (combined chlorine) is not sufficient to ensure complete conversion of trivalent arsenic 

to pentavalent arsenic.  Please see the Arsenic Facts section of the Performance Data Sheet for further information.

 

Avg. In. 

Avg. Eff. 

% Reduction  pH 

Pressure  Max Eff.  Inf. challenge 

Max Allowable

 

 

 

 

 

 

 

concentration 

concentration

 

 

 

 

 

 

 

mg/L 

mg/L

Arsenic (Pentavalent)  334.615 ug/L  5.0385 ug/L 

98.4% 

 

50psi 

19 ug/L 

   0.30±10% 

0.010

Barium Reduction 

10.2 mg/L 

0.207 mg/L 

97.9% 

7.24 

50psi 

0.3 mg/L 

   10.0±10% 

 2.0

Cadmium Reduction 

0.036 mg/L  0.0005 mg/L 

98.6% 

7.49 

50psi 

0.0007 

    0.3±10% 

0005

Chromium (Hexavalent)  0.15 mg/L 

0.013 mg/L 

91.3% 

7.24 

50psi 

0.03 

    0.3±10% 

0.1

Chromium (Trivalent) 

0.17 mg/L 

.01 mg/L 

94.1% 

7.24 

50psi 

0.01 

    0.03±10% 

0.1

Copper Reduction 

3.1 mg/L 

0.03 mg/L 

99.0% 

7.64 

50psi 

0.04 

    3.0±10% 

1.3

Cysts 

222,077#/ml 

10 #/ml 

99.99% 

 

 

58      minimum 50,000/mL   

Fluoride Reduction 

8.0 mg/L 

0.5 mg/L 

93.9% 

7.49 

50psi

 

0.7 

    8.0±10% 

1.5    

Lead Reduction 

0.15 mg/L 

0.002 mg/L 

98.6% 

7.49 

50psi 

0.003 

    0.15±10% 

0.010

Nitrate & Nitrite 

28.8 mg/L 

6.6 mg/L 

77.0% 

 

50 psi 

10 mg/L 

30±10% 

10.0

Nitrate 

26.0 mg/L 

6.1 mg/L 

76.5% 

 

50 psi 

10 mg/L 

27±10% 

10.0

Nitrite 

2.8 mg/L 

0.5 mg/L 

82.1% 

 

50 psi 

0.77mg/L 

3.0±10% 

1.0

Perchlorate 

0.10 mg/L 

0.003 mg/L 

96.5% 

7.39 

50 psi 

0.005 mg/L 

0.10±10% 

0.006

Radium 226/228 

25 pCi/L 

5 pCi/L 

80.0% 

7.24 

50psi 

5 pCi/L 

    25pCiL±10% 

5 pCi/L

Selenium 

0.10 

0.008 

92.0% 

 

50psi 

0.011 

    0.10±10% 

0.05

TDS 

765 

23 

96.8% 

7.84 

 

 

    750±40mg/L 

187

Turbidity 

10.2 mg/L 

0.26 mg/L 

97.5% 

 

 

0.83 

    11±1 NTU 

0.5 NTU

 

RECOVERY - 16.34% 

 

GALLONS - 17.32 GPD 

 

EFFICIENCY - 8.91%

Efficiency rating means the percentage of the influent water to the system that is available to the user as reverse osmosis treated water under operating 

conditions that approximate typical daily usage.

 

Recovery rating means the percentage of the influent water to the membrane portion of the system that is 

available to the�

There 

is an average of 4 gallons of reject water for every 1 gallon of product water produced. Testing performed under standard laboratory conditions, actual 

performance may vary. Refer to owners manual for further maintenance requirements and warranty information.

Phone: (623) 931-1977 

 

Fax: (623) 931-0191 

 

 

Email: wpmail@wattsind.

GENERAL USE CONDITIONS:

1. S�

.  Do not use 

with wate�

ed for cyst 

reduction may be used on disinfected water that may contain filterable cysts.

2. This system is acceptable for treatment of influent concentrations of no more than 27 mg/L nitrate and 3 mg/L nitrite in combination measured as 

N and is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa (40 psig) or greater.  If your water supply is under 40 
psi, Watts Premier recommends the use of a RO booster pump for proper operation. 

3. Operating Temperature: 

 

 

Maximum: 100°F (40.5°C) 

 

 

Minimum: 40° (4.4°)

4. Operating Water Pressure:   

 

Maximum: 85 psi (7.0kg/cm2)  

 

Minimum: 40 psi (2.8kg/cm2)

5. pH 

 

 

 

 

2 to 11

6. Hardness of more than 10 grains per gallon (170 ppm) may reduce TFM membrane life expectancy.

7. Recommend TDS (Total Dissolved Solids) not to exceed 1800 ppm.

Watts Premier Inc.

 1725 W. Williams Drive C-20

Phoenix, AZ 85027 USA

(623) 931-1977   [email protected]

Performance Data Sheet

B-RO5M-50, WP5-50

Summary of Contents for B-RO5M-50

































Reviews: