Watts Premier B-RO5M-50 Installation, Operation And Maintanance Manual Download Page 8

Page: 8 / 32

Page 8

AG-SS with Monitor Faucet Installation - Part# 116061

Step 6

Step 7

Gather and identify the faucet pieces.

Remove faucet and small parts from plastic bag.

Slip the gasket over the threaded stem to the faucet

ﬂange. From above the sink, feed the tubing and faucet

stem down through the 1¼ inch mounting hole in the

sink.

From below the sink, slide the tubing guide up the

threaded stem and follow it with the mounting nut, turning

the nut clockwise until fully tightened.

Insert the blue tubing (part# 610113), into the end of the

threaded stem. Push it all the way in and then pull on it

ﬁrmly to verify it is locked in place. (NOTE: this tubing will

also be used for the ﬁnal ﬁlter installation page 11)

Refer to

Black Tube Connection

and

Red Tube

Connection

steps on page 11 of this manual to complete

the faucet installation.

Remove the spout from the top of the faucet by pulling it

straight upward. SEE DRAWING

Remove the faucet knob by pinching the two locking

tabs inward and then pulling upward on the knob while

the tabs are pinched inward. Push the coin cell battery

into the battery holder behind the circuit board.

NOTE:

the + side of the battery goes against the gold metal

Note:

If using the AG-SS Monitor Air Gap Faucet , a 1 1/4” hole will be
required.

Step 8

Step 9

Note:

Replace the knob by centering it over the faucet and aligning the trough on the

inside of the faucet knob with the valve lever. Lower the knob making sure the

valve lever slides into the trough, making sure the knob top hole is centered

over the locking tabs. Push the knob all the way down until it locks in place.

Push the spout back into the top of the faucet so that it is fully seated and

push the frosted deﬂector down until fully seated. You may have to rotate the

deﬂector until it is in position to be fully seated.

After completing the installation of your RO system, you should see the green

light ﬂash at the base of the faucet while water is ﬂowing through the faucet

(the red light may ﬂash when system is ﬁrst turned on, this will turn

green following the initial tank ﬂush)

When the system is ready to be serviced (six to 12 months) you will see the

ﬂashing light switch from green to red, indicating it is time to replace your ﬁlter

cartridge(s).

Step 10

Summary of Contents for B-RO5M-50

































Search results

Summary of Contents for B-RO5M-50

Reviews:

Related manuals for B-RO5M-50

Brands by name

Popular brands

Watts Premier B-RO5M-50, Installation, Operation And Maintanance Manual

Search results

Summary of Contents for B-RO5M-50

Reviews:

Related manuals for B-RO5M-50

Brands by name

Popular brands