background image

 

SAFETY INSTRUCTIONS 

1.  Do not plug in unit if any of the external surfaces or electrical components 

are wet. 

 

2.  To avoid possible electric shock, special care should be taken since water 

may be present near electrical equipment. Unless referred to in these 
instructions, do not attempt repairs to the unit yourself. Contact the 
manufacture for service advice. 

 

3.  Do not operate this system if it has a damaged electrical cord or plug is 

malfunctioning, or has been dropped or damaged in any way. 

 

4.  Do not use this unit for anything other than its intended potable water 

application. The use of attachments not recommended, approved, or sold 
by the manufacturer/distributor may result in an unsafe condition. 

 

5.  Before doing any cleaning or maintenance, always unplug the unit. 

 

6.  Protect your unit from freezing. Drain all water from unit if freezing 

temperatures exist. 

 

RAW WATER QUALITY 

It is strongly recommended that you have your raw water professionally tested for 
dissolved mineral content, turbidly and microbiological activity.  Your UV 
disinfection system requires clean, clear water for optimum performance.  You 
should only operate your unit if the source water meets the following minimum 
standards: 

 

Turbidity

<1 NTU

Suspended Solids

<10mg/L

Colour

None

Total Iron

<0.3mg/L

Manganese

<0.5 mg/L

Hydrogen Sulphide

<0.5 mg/L

Hardness

<7 gpg

 

 

Where raw water conditions do not meet these minimum standards, pre-
treatment equipment such as an inline or automatic filter, ion exchange softener 
or an RO system must be installed.  Consult with your local water treatment 
specialist for advice. 

 

 

Where microbiological activity is indicated to be present in your water 
source, it is highly recommended that additional disinfection barriers be 
used in addition to your UV system.  This could include water well 
chlorination using a pellet dispenser, inline chlorine injection using a 
dosing pump and a contact tank, <1-micron absolute filtration or ozone 
injection.  The use of multiple barriers will assure safe drinking water in the 
event of the failure of any one of the disinfection methods. 

 

 

 

 

Summary of Contents for Excelight EL411AK

















Reviews: