background image

Waterco Aquamaster

I pg 41

Warranty - PLEASE READ

[Important note: The benefits under this warranty are in addition to other legal rights and remedies 

you may have in relation to Waterco products]

1.  These terms and conditions carefully, as failure to comply may affect your legal rights under this 

warranty; and

2.  Any operation instructions carefully before commencing use of any product manufactured by 

Waterco Limited (“Waterco”).

3.  Waterco manufactures quality pool and spa products to the highest standards using the most 

advanced technology and production procedures available.

WARRANTY COVER

If a defect occurs in any Waterco product during the warranty period, Waterco will at its discretion, 
repair the product or replace and install the defective part, free of charge provided that the defect 
results solely from poor workmanship or materials and subject to these terms and conditions.

Labour is covered by this warranty for a period of twelve months from the date of purchase or 
installation, within a 25 km (15 miles) radius of an authorized Waterco Service Agent.

The purchaser is responsible for any freight incurred.

Warranties are valid only within the original country of purchase. Our goods come with guarantees 
that cannot be excluded under the Australian Consumer Law [applicable only to Australian States 
and Territories]. You are entitled to a replacement or refund for a major failure and compensation for 
any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired 
or replaced if goods fail to be of acceptable quality and the failure does not amount to a major 
failure.

WARRANTY PERIOD

All products sold by Waterco are covered by a one year warranty. The exceptions to this are the 
products listed in the schedule (which also specifies relevant warranty periods). All warranty periods 
commence on the date of purchase by the end user.

The provisions of this warranty are not transferable and are in addition to and not in modification of 
or subtraction from any applicable statutory warranties, rights or remedies.

CONDITIONS OF WARRANTY

This warranty only applies where:
1.  The products requiring installation have been sold with installation included and have been 

installed by a licensed plumber, electrician or person who has completed an accredited course 
in swimming pool care and maintenance or a person with more than 12 months on the job 
learning

  or a person supervised by one of these people, in accordance with any written installation 

instructions provided.

2.  The products have been installed and operated in accordance with written instructions supplied
  by Waterco;
3.  The purchaser is able to provide proof of purchase that specifies the date of purchase;
4.  The product has been serviced or maintained regularly. 
5.  Installed in an area that is free from flooding or excessive outside contact with water; 
6.  Any pool and spa equipment has been used in water:

a.  With a temperature not exceeding 40

O

C degrees Celsius;

b.  With a pH range maintained between 7.2 – 7.6;
c.  That has been chemically balanced in accordance with the Langelier saturation index within 

a range of -0.2 to + 0.2 to ensure that it is not corrosive or scale forming;

d.  That is not salt water (other than mild saline water conditions which are compatible with 

swimming pool salt water chlorination systems) – unless otherwise stated by Waterco in both 
the respective product labels and brochures that it is suitable for seawater applications; and 

e.  That has been regularly treated with a sanitizing system using bromine, chlorine in one of 

its compound forms, or generated in-situ, in concentrations (doses) recommended by the 
relative state or territory health departments. (In areas outside of Australia please refer to the 
local health department recommendations before use);

7.  Electrical equipment has been adequately protected from salt air environments and from salt 

water; and

  All repairs and replacements shall be carried out by Waterco or its authorized service dealer, 

unless otherwise authorized in writing by Waterco.

  If an authorized service dealer is not available within 25 km (15 miles) of the purchaser’s area:

• The purchaser must contact the place of purchase or Waterco for further instructions and;
• The purchaser is responsible for any freight or infield labour costs.

Summary of Contents for Aquamaster

























Reviews: