background image

2

IMPORTANT SAFETY INSTRUCTIONS

Save these instructions

This appliance is not intended for use by persons (including 

children) with reduced physical, sensory and mental capabilities, 

or lack of experience and knowledge, unless they have been 

given supervision or instructions concerning use of the appliance 

by a person responsible for their safety. Children should be 

supervised to ensure that they do not play with the appliance. 

1.  This product contains Li-Ion batteries.  Do 

NOT

 abuse this product.  If you suspect any damage to the 

batteries, do 

NOT

 attempt to charge the robot, contact Water Tech Customer Service.

2.  Do 

NOT

 store the CX-1 near heat or an open flame.

3.  The safe temperature range for both use and storage is 41 to 113

°

F (5 to 45

°

C). Do not attempt to charge, 

use, or store the CX-1 in temperatures outside of this range. 

4.  Using any charger other than the one provided with the unit will cause damage and possible injury. 

Always charge the unit inside a dry, sheltered area.

5. 

Place the charger in a shaded dry area during both charging and storage.

 Keep away from 

direct sunlight and liquids.

6.  Maintain a minimum distance of 3m (10ft.) from the edge of the pool when recharging the batteries of the 

cleaner.

7.  Before operation, unplug the charging cable from the control box.
8.  Unit is 

NOT

 intended for 

COMMERCIAL USE. 

Unit is 

NOT

 intended for 

OPENING A POOL

.

9.  Do not enter the pool while the pool cleaner is working. When the robot is in sleep mode, it is safe to 

enter the pool.

10. Ensure the electrical outlet used for charging is protected by a ground fault circuit interrupter (GFCI) or 

an earth leakage interrupter (ELI). 

DO NOT use an extension cord or power strip.

11.  The pool cleaner must be charged for 1.5 - 2.5 hours before long term storage.
12. The sole purpose of this product is for use as a robotic pool cleaner as described in this manual; any 

modifications or other use will VOID the warranty.

13. Do not allow children to use, touch, or play near or around the unit and the charger.
14. Do not use if the unit or charger is damaged in any way.

15. 

MAKE SURE 

the robotic pool cleaner is unplugged from its power supply and turned off before opening 

the unit or performing any other maintenance.

16. 

It is recommended that you clean your filter and check the impeller to make sure it is free and clear of 

debris after every use.

17.  Disconnect the charger from the outlet when not in use.
18. If your robotic pool cleaner is not working as it should or has been dropped or damaged in any way, 

contact Water Tech Customer Service.

19. Save these instructions.  Refer to them frequently.  Provide these instructions to others who may use  

the product.

Before using your CX-1, please read the following warnings 

and read carefully through this Operator Manual.

Summary of Contents for 77000RR





























Reviews: