background image

?

25

• I put the robot in “Weekly” Cycle and now only 3 lights are ON, why is that?

• When in “Weekly” Cycle the robot will clean once a day for 7 days. When it is not cleaning, the robot

is in “Sleep Mode” which is indicated by the 3 lights. See Pages 7-8 of manual for more information 

on “Weekly Cleaning Cycle”.

• I put the robot in “1-Day” Cycle and now only the Battery Lights are ON, why is that?

• When in “1-Day” Cycle, the robot will clean for 2-hours and then enter “Sleep” mode indicated by the

light display. The robot will not wake itself from this “Sleep” mode. You must manually start the robot 

to begin the 2nd 2-hour cycle. See page 7 of the manual for more information.

• I finished charging my robot and now it won’t start, all the LEDs except for “Cleaning

Mode” are ON.

• This a safety feature to prevent the robot from starting accidentally.

• Turn the robot OFF and back ON using the Power (ON/OFF) Button.

• Refer to page 10 for more information.

• If this problem continues to occur, contact Water Tech Customer Service.

• How does the CX-1 drive itself into the pool?

• Place the robot with the FORWARD arrow pointing TOWARDS the pool. When the robot turns ON, it

will drive forward over the edge and into the pool.

• THIS FEATURE DOES NOT WORK FOR ABOVE GROUND POOLS!

• What happens if I do not cover the charging jack with the rubber plug?

• The charging jack could interfere with the software of the robot and cause strange behavior.  

• Slow discharge of the batteries will occur and shorten the run time.

• The charging pins will corrode and reduce the life of the robot.

• How do I store my robot for the winter?

• Charge your robot for 1.5 to 2.5 hours before winter storage. Make sure the robot is stored in a warm,

dry, indoor shelter. See page 19 for more information on long term storage.

• Can I run the robot without the filter bag?

• No, not intended for use without a filter.

• Unfiltered debris may jam or obstruct the impeller and/or integral components.

• If pump motor jammed:  

Turn power OFF;

 check the impellers for visible obstructions. Refer to page 17 for further instructions.

• Can I leave the robot out in the rain?

• If the charger is NOT connected to the robot, it is safe to leave out in the rain.

• Charge the robot in a dry, shaded location.

• My robot is falling off the wall, is this normal?

• Yes, when the robot reaches the surface, it is designed to fall off the wall rather than drive back down.

• This saves energy, and the robot reorients itself after submerging.

• Can I use my robot to clean a commercial / olympic size pool?

• Please be aware, runtime on fully charged battery packs may not be sufficient for

commercial / olympic sized pools.

• Can I open the pool with my CX-1?

• The CX-1 is not intended for cleaning a pool just after opening.

CX-1 FAQs

Summary of Contents for 77000RR





























Reviews: