Water Right IM-1044 Installation Instructions & Owner'S Manual Download Page 24

Page: 24 / 28

1” PVC MALE NPT ELBOW

Legacy Part # Current Part #

Description

Qty.

CV3007

100246197

1” PVC male NPT

elbow assembly

3/4” & 1” PVC SOLVENT ELBOW

Legacy Part # Current Part #

Description

Qty.

CV3007-01

100246198 3/4” & 1” PVC solvent

elbow assembly

1” BRASS SWEAT

Legacy Part # Current Part #

Description

Qty.

CV3007-02

100246199

1” brass sweat

assembly

3/4” BRASS SWEAT

Legacy Part # Current Part #

Description

Qty.

CV3007-03

100249846

3/4” brass

sweat assembly

3/4 BRASS SHARK BITE

Legacy Part # Current Part #

Description

Qty.

CV3007-12

100249847

3/4” brass shark

bite assembly

1” BRASS SHARK BITE

Legacy Part # Current Part #

Description

Qty.

CV3007-13

100249848

1” brass shark

bite assembly

3/4” JOHN GUEST ELBOW

Legacy Part # Current Part #

Description

Qty.

CV3007-15

100246200

3/4” john guest

elbow assembly

1” JOHN GUEST

Legacy Part # Current Part #

Description

Qty.

CV3007-17

100245045

1” john guest

assembly

1-1/4” & 1-1/2” BRASS SWEAT

Legacy Part # Current Part #

Description

Qty.

CV3007-09

100243922 1-1/4” & 1-1/2” brass

sweat assembly

1-1/4” & 1-1/2” PVC SOLVENT

Legacy Part # Current Part #

Description

Qty.

CV3007-07

100243375 1-1/4” & 1-1/2” PVC

solvent assembly

1” PLASTIC MALE NPT

Legacy Part # Current Part #

Description

Qty.

CV3007-04

100249846

1” plastic male NPT

assembly

1-1/4” PLASTIC MALE NPT

Legacy Part # Current Part #

Description

Qty.

CV3007-05

100243921

1-1/4” plastic male

assembly

Item #

Legacy

Part #

Current

Part #

Description

Qty .

CV3151

100246287 Nut, 1” quick connect

CV3150

100246286 Split ring

CV3105

100246272 O-ring 215

NOTE: Not all available ﬁ ttings are

displayed below. Contact

manufacturer for optional
ﬁ ttings.

For All Assemblies

INSTALLATION FITTING ASSEMBLIES

Summary of Contents for IM-1044




























Search results

Summary of Contents for IM-1044

Reviews:

Related manuals for IM-1044

Brands by name

Popular brands

Water Right IM-1044, Installation Instructions & Owner'S Manual

Search results

Summary of Contents for IM-1044

Reviews:

Related manuals for IM-1044

Brands by name

Popular brands