background image

26

Water Softener Limited Warranty

Congratulations. You have purchased one of the fi nest water treatment systems available. In the unlikely 
event of a problem due to defects in material and workmanship, we proudly warrant our water softeners to 
the original owner, when installed in accordance with Water-Right

®

 specifi cations. This warranty is effective 

from the date of original installation for:

A period of TEN YEARS: 

 

 Fiberglass mineral tanks 13” and smaller; except for damages 
due to freezing, high pressure (120 PSI and above), extreme 
temperature (100°F and above) or a vacuum on the system. 

A period of FIVE YEARS: 

 

The complete valve.

 

 

 

 

 

Fiberglass mineral tanks 14” and larger.

     The 

salt 

storage 

container.

A period of ONE YEAR: 

 

All other softener components.

Any part found defective within the terms of this warranty will be repaired or replaced by the dealer. You pay 
only freight from our factory and local dealer charges. To obtain local warranty service, contact original dealer 
or an authorized service dealer. If no authorized dealer is located in your area, please ship defective part or 
component freight prepaid to Water-Right, Inc., 1900 Prospect Ct., Appleton, Wisconsin 54914. Water-Right,  
at its discretion, will repair or replace the part or component at its expense and return part freight collect.

The above provisions of the warranty are valid as long as the unit is connected in compliance with local 
plumbing codes and in an equivalent manner and condition of the original installation and is owned by the 
original owner.
 
This warranty does not cover damages due to accident, fi re, fl ood, freezing, or any other Act of God.  
We are not responsible for damages due to change in water conditions, misapplication, misuse, neglect, 
vacuum, oxidizing agents, alteration, or lack of maintenance. No responsibility is assumed for loss of use 
of the unit, inconvenience, loss or damage to real or personal property or any incidental or consequential 
damages. Furthermore, we assume no liability and extend no warranties, express or implied, for the use 
of this product with a non-potable water source. 

To the extent permitted by law, Water-Right disclaims 

all implied warranties, including without limitation warranties of merchantability and fi tness for 
particular purpose; to the extent required by law, any such implied warranties are limited in duration 
to the aforementioned period specifi ed above.

Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty 
lasts. Consequently, the above limitation may not apply to you.

This warranty gives you specifi c legal rights, and you may also have other rights which vary from state    
to state.

Summary of Contents for IM-1044





























Reviews: