Water Care Ion Pro Series Installation Instructions & Owner'S Manual Download Page 30

30

WaterCare

®

 Water Conditioner Limited Warranty

Congratulations. You have purchased one of the fi nest water treatment systems available. In the unlikely event 
of a problem due to defects in material and workmanship, Water-Right

®

 proudly warrants our WaterCare water 

conditioners to the original owner, at original installation location, when installed in accordance with Water-Right 
specifi cations from the date of original installation as follows:

For the LIFETIME of the original owner:   Media tank, except for damages due to freezing, 

high pressure (120 PSI and above), extreme temperature 
(100° F and above) or a vacuum on the system.

For a period of TEN YEARS: 

Brine tank.

For a period of FIVE YEARS: 

Complete valve.

For a period of ONE YEAR: 

All other parts and components.

Any part found defective within the terms of this warranty will be repaired or replaced by the dealer at the 
manufacturer’s discretion. You pay only freight from our factory and local dealer charges. To obtain local warranty 
service, contact original dealer. If original dealer is unknown, contact Water-Right for authorized service dealer in 
your area. If no authorized dealer is located in your area, please ship defective part or component freight prepaid to:

 Water-Right, 

Inc.

 

1900 Prospect Ct.

 

Appleton, Wisconsin 54914

Water-Right, at its discretion, will repair or replace the part or component at its expense and return part freight collect.

The above provisions of the warranty are valid as long as the unit is connected in compliance with local plumbing 
codes and in an equivalent manner and condition of the original installation and is owned by the original owner.
 
This warranty does not cover expendable or misapplied medias, or damages due to accident, fi re, fl ood, 
freezing, or any other Act of God. Water-Right is not responsible for damages due to change in water conditions, 
misapplication, misuse, neglect, vacuum, oxidizing agents, alteration, or lack of maintenance. No responsibility is 
assumed for loss of use of the unit, inconvenience, loss or damage to real or personal property or any incidental 
or consequential damages. Furthermore, we assume no liability and extend no warranties, express or implied, 
for the use of this product with a non-potable water source. 

To the extent permitted by law, Water-Right 

disclaims all implied warranties, including without limitation warranties of merchantability and fi tness for 
particular purpose; to the extent required by law, any such implied warranties are limited in duration to 
the period specifi ed above for the specifi ed components.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply 
to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above 
limitation or exclusion may not apply to you. This warranty gives you specifi c legal rights, and you may also have 
other rights which vary from state to state.

Summary of Contents for Ion Pro Series

































Reviews: