background image

 

 

12. EC-Declaration of Conformity  

__________________________________________________________ 

  
 

Declaration of Conformity   

  

Wasserlab 

 
 

Navarra de Tratamiento de Agua S. L. declares that this 

 

Water Purification Equipment: 

Model:  Micromatic 

Brand:  Wasserlab 

 

Manufactured  and  certified  by  Navarra  de  Tratamiento  de  Agua  S.L.,  complies  with  the 
Directives and Regulations  
  

 -   2006/95/CE Low Voltage Directive  

 

 -  

UNE/EN  61000-3–2:2006  and  61000–3–3:2009  Electromagnetic  Compatibility 
(EMC)

 

  

-   UNE/EN  61010-1:2002  and  61010-1  Corr.:  2003,  Security  requirements  for 

electronic measuring, control and laboratory use equipments  
  

-   2004/108/CE Electromagnetic Compatibility Directive (Royal Decree 1580/2006)  

  

-   UNE-EN  61326-1:  2006  Electrical material for measurement,  control,  and  usage 

in laboratories.  Electromagnetic compatibility requirements (EMC)  

 
 
The equipment complies with the directives and standards mentioned when installed 
according to manufacturer's specifications.  

 
Signed for and on behalf of Navarra de Tratamiento del agua

 

  
 

  

 

 
 
 
 

Carlos Irigoyen 

General Manager 

 

Barbatáin, 20.03.17 

 
 

Navarra de Tratamiento el Agua S.L. 

Pol. Ind. Comarca II, C/A Nº 26 

31191-Barbatáin – Navarra, Spain 

CIF: ESB31637580 

Summary of Contents for Micromatic





















Reviews: