background image

WARN INDUSTRIES

PAGE 2

70557A2

I. TABLE OF CONTENTS

Parts List

page 2

Tools Required

page 2

Installation

page 3-5

Winch and Lowering Plow Instructions

page 6-7

Maintenance/Care

page 8

II.  PARTS LIST

Part Number

Qty

Description

A1

1

Plow Mount

B1

4

5/16-18 x 1 3/8” x 2” u-bolt

B2

8

5/16” Flat Washer

B3

8

5/16-18 Lock Nut

Caution

Mo

Mo

Mo

Mo

Moving P

ving P

ving P

ving P

ving Par

ar

ar

ar

arts Entanglement Hazard

ts Entanglement Hazard

ts Entanglement Hazard

ts Entanglement Hazard

ts Entanglement Hazard

FFFFFailure t

ailure t

ailure t

ailure t

ailure to obser

o obser

o obser

o obser

o observvvvve these instructions could lead t

e these instructions could lead t

e these instructions could lead t

e these instructions could lead t

e these instructions could lead to minor or moderat

o minor or moderat

o minor or moderat

o minor or moderat

o minor or moderate injur

e injur

e injur

e injur

e injuryyyyy.....

‰

Always 

take time to fully read and understand the installation and Operations Guide included with this product.

‰

Never 

operate this product if you are under 16 years of age.

‰

Never 

operate this product when under the influence of drugs, alcohol or medications.

Read installation and operating instructions thoroughly.

Notice

Equipment Damage

‰

Always 

refer to the Installation and Specification Guide, supplied in the winch kit, for all wiring schematics and specific details

on how to wire this WARN product to your vehicle.

‰

Never 

overtighten the j-bolt to the bracket. Doing so will pinch the winch cable against the bracket, damaging the cable.

‰

Always 

put the end of the actuator cable through the slot in the Termination Bracket. Terminating the cable through any other

hole in the bracket will cause the bracket to not function properly and will drastically reduce the life of the actuator cable.

Read installation and operating instructions thoroughly.

III.  TOOLS REQUIRED

- Ratchet
- 10mm Socket
- 1/2” Socket
- 3/8” Drill

Note:

Please refer to the Winch and Lowering Plow Instructions, p 5-6,  if you plan to lower your plow using a
winch.

B1

A1

B3

B2

Summary of Contents for 70558









Reviews: