background image

• PRESS      

or     to adjust your target temperature. 

PRESS OK 

to finish.

Operating in Manual Mode

NOTE:

 The target temperature must be above the current air and/or floor temperatures for the heating to be activated. 

Operating in Schedule Mode

Warranty

The weekly schedule can be configured to operate on 3 schedules, (Weekdays, Saturday, Sunday) or 7 schedules, with 

each day on own. The schedule format can be changed in the advanced settings.

• With the heating schedule mode displayed      , 

PRESS

 and 

HOLD SET

 for 3 seconds until 1 - 5 block begins to flash.   

• 

PRESS SET

 again to begin setting the start time of the 1st period.

• 

PRESS

      or      to adjust the parameters.

• 

PRESS SET

 when done to move to the next adjustment (target temperature / next period).  

• Repeat the steps above to program the time and target temperatures for the other periods.

• 

PRESS OK 

to finish.

To reset your heating schedule to factory default 

PRESS

 and 

HOLD

      for 3 seconds when the heating schedule mode

is displayed      

ConF

 will flash, 

PRESS SET, ProG 

will flash,

 PRESS OK

 to accept.

NOTE: 

If set to 7 day in advanced settings each day will have to be programmed individually. 

Setting a Heating Schedule

When the thermostat is set to heating schedule mode, setting a temporary override allows you to set a temperature 
you would like the thermostat to reach until the next period. 

PRESS

      or      to set the target temperature. When a 

temporary override is set both       and       will be displayed.

The thermostat will resume its normal schedule at the start of the next period, alternatively to cancel a temporary 

override and return to heating schedule mode 

PRESS OK.

Setting a Temporary Override

Warmup warrants this product, to be free from defects in the workmanship or materials, under normal use and service, 

for a period of 1 year from the date of purchase by the consumer. If at any time during the warranty period the product 

is determined to be defective, Warmup shall repair or replace it, at Warmup’s discretion.
If the product is defective, please either,

 

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it,  

 or

 

(ii) contact Warmup. Warmup will determine whether the product should be returned, or replaced.

This warranty does not cover removal or reinstallation costs, and shall not apply if it is shown by Warmup that the 

defect or malfunction was caused by damage which occurred while the product was in the possession of the end user.
Warmup’s sole responsibility shall be to repair or replace the product within the terms stated above. 

WARMUP SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL 

DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESSED OR IMPLIED, OR ANY 

OTHER FAILURE OF THIS PRODUCT. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY WARMUP MAKES ON THIS PRODUCT. 

THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 

PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE 1 YEAR DURATION OF THIS WARRANTY. 

This Warranty does not affect your statutory rights. 

Please register your product at: http://www.warmup.co.uk/

Warmup PLC

702 & 704 Tudor Estate

Abbey Road

London

NW10 7UW

Web:

     

www.warmup.co.uk

Email:

 [email protected]

Tel:

 

0345 345 2288

Contact Details

4

Warmup - IM - One - v1.0 2018-07-31.indd   4

31/07/2018   10:58:32

Summary of Contents for One









Reviews: