background image

To access advances setting, 

PRESS

 and 

HOLD

      and      simultaneously for 5 seconds.

PRESS

 

SET

 

to navigate through the different advanced settings. Use      or      to adjust the setting. 

PRESS OK

 to

exit advanced settings

Warmup One - Programmable Thermostat

EN -

 OPERATING INSTRUCTIONS

1 2

6

3

4

5

8

7

9

10

16
15

11

13

14

12

1 - 

Set Button

2 - 

OK Button

3 - 

Power Button

4 - 

Navigation Buttons

5 - 

Factory Reset (Insert pin)

6 - 

Manual Mode

7 - 

Displayed When Programming

8 - 

Heating Schedule Active

9 - 

Heating Schedule Mode

10 - 

Advanced Setting Configuration 

• PRESS SET 

when the thermostat displays current floor/air temperature.

• PRESS SET

 again, the minutes will flash.

 PRESS      

or     to set the minutes.

• PRESS SET 

again, the hour will flash.

 PRESS     

 or     to set the hour.

• PRESS SET 

again, the day of the week will flash (1-7).

 PRESS   

   or     to set the day.

 

PRESS SET 

to finish.

To view the current time 

PRESS SET 

while the thermostat is idle. The thermostat will revert to its idle display after 20 

seconds or if you 

PRESS OK.

• PRESS 

and

 HOLD OK 

for 3 seconds to switch from schedule      to manual mode.

• PRESS OK

 once to return to schedule mode. 

Manual Mode - 

Allows you to set a fixed temperature for the thermostat to maintain. 

Heating Schedule -

 Setting a Heating Schedule allows you to set comfort temperatures at set times throughout the day. 

The thermostat can bet set so that MON - FRI (1 - 5) is programmed as a block with SAT (6) and SUN (7) programmed 

individually. Alternatively the thermostat can set so that you program each day individually, see advanced settings on 

how to switch between schedule settings.

Typically when setting a 6 period schedule, periods 1, 3 and 5 will be heating periods with periods 2, 4 and 6 being 

setback or “Off”. To switch to a 4 period schedule see advanced settings.

11 - 

Displays current Floor/Air Temperature

12 - 

1-7 Days of the Week

13 - 

Heating Indication

14 - 

Schedule Period

15 - 

Temperature (Clock)

16 - 

 

 

Air mode Floor mode Air Mode with 

Floor Limit

Setting Time/Day

Setting Manual Mode or Heating Schedule

Period

Time

Temperature Comment

Schedule Period

Period 1

06:00

20°C

Wake up. Initial heating period of the day

Period 2

08:00

15°C

Leaving the house.

Period 3

17:30

22°C

Back for lunch 

Period 4 

17:30

22°C

Leave house after lunch

Period 5

17:30

22°C

Back home 

Period 6

22:00

15°C

Go to bed. Final period of the day

3

Warmup - IM - One - v1.0 2018-07-31.indd   3

31/07/2018   10:58:31

Summary of Contents for One









Reviews: