background image

 

 

~ 2 ~

 

Installation and operation manual DC 

1.

 

Warning 

 

First and foremost, check the condition of your heat pump as soon as you receive it, 
write any reservations you have about its state on the delivery note if you have any 
doubts  or  a  problem  and  send  a  registered  letter  to  your  installer or directly  to  the 
manufacturer within 48 hours. After this period, no claim will be accepted. 

 

1.1

 

 Important information 

To properly install your heat pump, read this manual carefully. We will not be liable 
for any injury to persons or damage to the machine due to any errors that might occur 
during installation. 

-

 

The installation of this heat pump must be carried out by qualified personnel, 

-

 

This  heat  pump  meets  the  manufacturing  and  communication  standards  defined 
by FPP's DTP10 and NFPAC, 

-

 

The maintenance of this heat pump must be carried out as set out in this manual, 

-

 

Only use original spare parts supplied by the manufacturer, 

-

 

Failure to follow these instructions or the information in this manual will void the 
heat pump's guarantee. 

 

 

2.

 

Your heat pump 

 

2.1

 

 Main features 

Your heat pump must not be used for any purpose other than to HEAT your pool. Its 
choice was determined following a personalized heat budget and it cannot be used for 
other pools until a new heat budget has been carried out. 

Your  heat  pump  is  one  of  the  most  efficient  and  environmentally  friendly  heaters, 
using R32 gas. 

 

 

 

 

Summary of Contents for DC55



















Reviews: