background image

 

Industries 1994 LTD 

PO Box 58652 Greenmount, Auckland 

WWW.Warmington.co.nz

 

 

 
 
 

S:\data\Word\spec. sheets\eclipse-crystal eclipse\Free Standing Eclipse 11-07-06.doc                                   

Created on 10/07/2006 10:09 a.m.                        Page 3 of 15 

 

All dimensions are in millimetres mm 

All dimensions are minimums 

Ensure That You Have The Correct 
and current Installation Details For 
The Size of The Warmington Fire 
That is to be installed. 

Keep these Instructions for future reference. 

Fire and flue system to comply to AS/NZS 2918 

Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification 

INSTALLATION ORDER OF OPERATION 

 
 

Prior to Construction and Installation   

Important Notes:

 

 

1)

 

Install to AS/NZS 2918: 2001. 

2)

 

Install to manufacture’s specifications. 

3)

 

All new installations require a permit. 

4)

 

For special requirements concerning materials (timber mantle and surrounds) within close proximity of Warmington 
products, please contact your local Warmington Technical Consultant. 

 

Stage 1: 

Frame Construction Procedure by Builder.

 

 

5)

 

Mark out flue centre. 

6)

 

Mark out heat cell clearance requirements. 

7)

 

Build timber framing to heat cell clearances and chimney chase clearance requirements. 

8)

 

Ensure that front face of heat cell clearance alcove is left open and unframed to enable installation of the firebox and 
adaptor.  The chimney chase is left unlined for installation of the flue. 

9)

 

Construct plinth only, to require height. * 

 

 

 

Stage 2: 

Install Procedure by Certified “Warmington Installer” only.

 

 

10)

 

Fit fire to plinth. 

11)

 

Fit adaptor to Firebox. 

12)

 

Fit heat cell cabinet to firebox. 

13)

 

Fit flue system. 

14)

 

Fit cowl and flashing system. 

15)

 

Fit fascia kit. 

16)

 

Fit vents to heat cell alcove and chimney chase, to cool the heat cell and ensure efficiency of CAITEC

 Technology. 

 

 

Stage 3: 

Finishing Procedure by Builder.

 

 

17)

 

Construct hearth to required thickness. * 

18)

 

Finish framing of heat cell alcove. 

19)

 

Close in heat cell alcove and chimney chase. 

20)

 

Finish heat cell alcove and hearth to customer’s requirements (e.g. paint / tiles). 

21)

 

Builder or Owner may install the vent in the Alcove as the building project may not be finished. 

 
Note:  certified installer can install hearth and plinth. 

 

 

 

Summary of Contents for 780
















Reviews: