WAREMA WMS Wall-mounted transmitter plus Operating And Installation Instructions Download Page 9

9

2018151_d•en•2019-10-01

We reserve the right to make technical changes

IUTCCE

O

When you delete a receiver from the network, 

it can no longer be operated via other transmit-

ters. It must be relearned into a network.

IUTCCE

O

It only makes sense to delete products via the 

WMS Wall-mounted transmitter plus in smaller 

networks (two to three awnings or roller shut-

ters). In more complex networks and when 

routing tables are used, a hand-held transmitter 

comfort or a central control unit should be used 

for deletion.

Maintenance

Replacing the batteries in the WMS Wall-mount-

ed transmitter plus

Replace the battery if the transmission LED lights up 

orange after the WMS Wall-mounted transmitter plus is 

activated. If the battery is fully depleted, the WMS Wall-

mounted transmitter plus can no longer be activated. 

 

 

When inserting a new battery (coin cell type CR 2032), 

make sure that the polarity matches: the positive termi-

nal (+) of the battery should face up (visible) and the 

negative terminal (-) should face down (see 

Fig. 4)

 

 

Only touch the battery on its edge.

 

 

When inserting the battery, make sure that it is pushed 

to one side under the contacts.

 

 

Use a high-grade battery – inexpensive batteries may 

leak and damage the device. If the device will not be 

used for an extended period of time, please remove 

the battery.

Dismantling the WMS Wall-mounted transmitter 

plus

 

 

To remove the WMS Wall-mounted transmitter plus 

(e.g. to replace the battery), carefully pull the clipped 

wall-mounted transmitter off the frame. 

 

 

Hold onto the central frame/plate, as it automatically 

comes loose when the wall-mounted transmitter is 

removed.

Liability

Failure to comply with the product information in these 

instructions and use of the unit in a manner other than its 

intended use may result in a refusal by the manufacturer to 

honour warranty claims for product damage. In this case, 

liability for consequential damage to persons or property 

will also be excluded. Observe the information in the op-

erating instructions for your sun shading system. Liability 

is also excluded for damage to the sun shading system 

resulting from operation while iced over.

Disposal

After use, the device and the batteries must be disposed 

of according to legal regulations or brought to your local 

recycling centre.

Summary of Contents for WMS Wall-mounted transmitter plus











Reviews: