3
!
Safety Information
1. To reduce the risk of electric shock, ensure the electricity
has been turned off at the circuit breaker or fuse box
before you begin.
2. All wiring must be in accordance with the National Electrical
Code “ANSI/NFPA 70-1999” and local electrical codes.
Electrical installation should be performed by a qualified
licensed electrician.
4. The fan must be mounted with a minimum of 7 ft
(2.1m) clearance from the trailing edge of the blades
to the floor.
5. Do not operate the reversing switch while the fan blades
are in motion. You must turn the fan off and stop the
blades before you reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and
other items, use caution when working around
or cleaning the fan.
8. Electrical diagrams are for reference only. Light
kits that are not packed with the fan must be UL
listed and marked suitable for use with the model
fan you are installing. Switches must be UL General
Use Switches. Refer to the instructions packaged
with the light kits and switches for proper assembly.
9. After making electrical connections,spliced conductors
should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
10. All setscrews must be checked and retightened where
necessary before installation.
WARNING: Remove the rubber motor stops on the bottom
of the fan before installing the blades or testing the motor.
WARNING; To reduce the risk of fire or electric shock, do
not use this fan with any solid-state speed control device.
WARNING: To avoid possible electrical shock, turn the
electricity off at the main fuse box before wiring. If you feel
you do not have enough electrical wiring knowledge or
experience, contact a licensed electrician.
WARNING: Electrical diagrams are for reference only.
Optional use of any light kit shall be UL-listed and marked
suitable for use with this fan.
WARNING: To reduce the risk of fire or electric shock, this
fan should only be used with fan speed control part no.
!
!
!
!
!
!
This equipment has been tested and found to comply with the limits for a Class B digital devico,pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If his equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION; Amy changes or modifications not expressly approved by the grantee of this device could void the user.s authority to operate
the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device
may not cause harmful intarferance,and (2)thie device must accept any interference received, including interference that may cause
undesired opereti0n.
!
WARNING: To Reduce The Risk Of Personal Injury,Do Not
Bend The Blade Brackets When Installing The Brackets,
Balancing The Blades, Or Cleaning The Fan.Do Not Insert
Foreign Objects In Between Rotating Fan Blades.
!
WARNING: To reduce the risk of electric shock, this fan
must be installed with an isolating wall switch.
!
WARNING: Check that the outlet box is securely and the
ceiling-suspended fan is mount to put let box marked
acceptable for fan support of 22.7 kg(50 Ibs)or less.
CAUTION:To reduce the risk of personal injury,use only
the screws provided with the outlet box
3.The weight of the fan is 8.2kg (18lb).
to reduce the risk of fire, wlectric shock,
or personal Injury, mount to outlet box marked
acceptable for fan support of 22.7 kg (50 Ibs)or less
and use mounting screws provided with the outlet
box. most outlet boxes commonly used for the
support of luminaires are not acceptable for fan
support and may need to be replaced.consult a
qualified electrician If In doubt.
INTSTRUCTION
