background image

30

177-999H

T100 Medium Pressure Tool Kit

The T100 Medium Pressure Tool Kit (Part No. 177-800) contains 

the tools illustrated below. These tools are used to assist in 

the repair and maintenance of the T100K and T100M. See the 

maintenance sections of this manual for specific application.

T100 Series Medium - Tool Kit and Pump Storage

1

W0525C

3

7

5

6

2

8

4

9

WARNING:  Item  9,  M10  Diaphragm  Plate  Eyebolt  is 

used to lift Diaphragm Plate (52) only. Do not use to 

lift entire pump. Attempting to lift entire pump with Eyebolt 

(9) may cause personal injury or damage to equipment.

CAUTION:  If the pump is to be stored more than six months 

take the following steps to protect against corrosion:

After Shut Down of the pump:

1.  Drain all process fluid from pump. Do not drain oil from the 

pump.

CAUTION  -  Do  not  store  the  pump  without  oil  in  the 

reservoir.

2.  Flush the fluid end of the pump with a corrosion inhibitor that 

is compatible with the diaphragm material and process fluid.

3.  Coat camshaft or crankshaft with rust preventative; wrap 

with wax-impregnated cloth and then with waterproof tape.

4.  Plug the suction and discharge ports of the pump to protect 

against dirt and moisture.

5.   Store in a clean, dry place.

Prior to Start-up of the pump:

1.  Drain  and  refill  the  hydraulic  end  of  the  pump  with  the 

appropriate Hydra-Oil.

Pump Storage for T100 Medium 

Pressure

Ref.   

                                               Quantity/ 

No. Tool Part No. 

Tool Description                       Kit 

1  177-393 

Stud Extender .....................................4

2    177-392 

Clip, E-style .........................................4

3  177-910 

Check Valve Extractor  ........................1

4   177-915 

Check Valve Extractor .........................1

5   A03-124-1200 

Check Valve Extractor Lever   .............1

6   177-157 

Thread Adapter, Check Valve Extractor  

 

 

to Slide Hammer  ................................1

7   177-136 

Outlet Check Valve Extractor, NPT .....1

8   177-140 

Outlet Check Valve Extractor,  

  

Flange .................................................1

9   177-058 

Eyebolt, M10 ........................................2

                                                 

 

 
 Part Number      Description                 Quantity
 177-149

 

   Screw, M8 

 

 

177-312

 

   Guide, Spring 

 

1

 177-355

 

   Rod, Bias spring 

 

1  

 177-183 

   

Spring, Bias 

 

 

177-050

 

   Screw, M5 

 

2

 177-145

 

   Arm, Valve 

 

1      

 177-190 

   

Clamp, Diaphragm 

 

1

 177-359

 

   Screw, M8 

 

1      

 T100 Medium Pressure Bias Rod Assembly Kit    

 Contents

 

(Part No. 177-802)

 

                                                 

 

 

Part Number      Description                 Quantity

 177-802

 

   Bias Rod Assembly   

 

177-906

 

   Valve, Air bleed 

 

3

 177-904

 

   Valve, Underfill 

 

3      

 177-905 

   

Valve, Overfill 

 

3

 

 

177-009 

   

Valve, Spool 

 

3      

 177-013

 

   Gasket, Diaphragm plate 

1      

T100 Medium  Hydraulic End Kit Contents

 

 

(Part No. 177-801) 

T100 Series Medium  

Replacement Parts Kits

Summary of Contents for Hydra-Cell T100 Series

































Reviews: