background image

Page | 1 

 

PREFACE

 

 

Thank you for purchasing a Wanco portable generator set. This manual contains important safety 

and operating information - please read the complete manual before attempting to operate the 

generator. 

All information in this publication is based on the latest product information available at the time of 

approval for printing. We reserve the right to make changes at any time without notice. 

No part of this publication may be reproduced without written permission. 

Throughout this manual pay special attention to statements preceded by the following signal 

words: 

Failure to properly follow these precautions is likely to result in 

property damage, serious injury or death 

Failure to properly follow these precautions can result in property 

damage, serious injury or death 

Indicates a possibility of personal injury or equipment damage if 

instructions are not followed 

 

Gives helpful information. 

 

If you need assistance with your generator set, please contact our service department: 

Wanco Inc. 

5870 Tennyson Street 

Arvada, Colorado 80003 

303-427-5700 

fax 303-427-5725 

www.wanco.com 

[email protected] 

Summary of Contents for WI3000P





























Reviews: