manualshive.com logo in svg

Waltron AQUALERT Aqualyzer 3051, Instruction Manual, Page: 30 / 70

Share
Download
Waltron AQUALERT Aqualyzer 3051 Instruction Manual Download Page 30

 

 

 

 

 

 

 

Analyzer Initial Start-Up 

29 

Waltron User Manual 

3051 Hardness Analyzer 

4 

ANALYZER INITIAL START-UP 

 

 

Before proceeding with analyzer start-up it is absolutely 
necessary to check that all procedures for a proper 
installation and reagent preparation have been made.  
Please verify that all the suggestions and recommendations 
have been respected.  

 

4.1 

PREPARING THE ANALYZER FOR START-UP 

Once installation is complete, proceed as follows to prepare the analyzer for online operation :  
 

1.

 

Connect the sample line inlet tubing (or filtered sample outlet coming from optional 
filtration system) to the fast-loop reservoir installed on the left side of the analyzer  

2.

 

Connect the drain fitting of the fast-loop reservoir to the waste line  

3.

 

Put the reagent inlet tubings into the appropriate reagent containers 

a.

 

Reagent 1 = Cresolphthalein Reagent 

b.

 

Reagent 2 = Ethanolamine Reagent 

4.

 

Put the calibration solution inlet tubing into the calibration solution positioned beneath 
the analyzer    

5.

 

Connect the analyzer drain tubing to waste drain line  

 

WARNING! 

The drain of the analyzer must be at ambient pressure with 
no restriction. Please verify that this condition has been 
strictly respected during initial start-up procedures.  

 
6.

 

Check sample presence in fast-loop reservoir and adjust the sample flowrate so that there 
is complete reservoir discharge when a finger is covering the hole at the top of the 
stainless steel drain line 

7.

 

Turn the analyzer on using the switch in the electronics compartment 

8.

 

Perform reagents prime (see Section 6.1) 

9.

 

Perform calibration (see Section 6.2 & 6.3) 

10.

 

Set the analyzer to online mode (see Section 6.5)  

 

 
 

Summary of Contents for AQUALERT Aqualyzer 3051







































































Reviews:

No comments