17
16
1 General
1.1
Identification of Model Versions
Models:
Automatic Spray Guns PILOT WA 110
Type:
PILOT WA 110
V 20 340
Manufacturer:
WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 00 49 202 / 787-0
Fax: 00 49 202 / 787-2217
www.walther-pilot.de • Email: [email protected]
1.2
Normal Use
The automatic spray gun PILOT WA 110 is exclusively designed for use with sprayable
materials.
•
paints and lacquers
•
greases, oils and corrosion preventives
•
adhesive compounds
•
separating agent
•
ceramic glazes
•
pickling solutions
Should the materials which you want to spray not be listed above, please contact
WALTHER Spritz- und Lackiersysteme for further and detailed information.
Please note that sprayable materials may only be applied to work pieces and/ or
similar items. The temperature of the spraying materials shall never exceed 80
degrees Celsius. The model PILOT WA 110 is not designed for manual operation,
and must be installed in a suitable gun mounting device.
The term normal use also implies that any and all safety warnings, operational hand-
ling details, etc., as stated in these operating instructions, must be carefully read,
understood and duly complied with.
This equipment complies with the explosion protection requirements of Directive
2014/34/EU (ATEX) for the explosion group, equipment category and temperature
class indicated on the type plate. When using the equipment, the requirements spe-
cified in these Operating Instructions must be observed at all times.
The technical data indicated on the equipment rating plates and the specifications in
the chapter "Technical Data" must be complied with at all times and must not be
exceeded. An overloading of the equipment must be ruled out.
The equipment may be used in potentially explosive atmospheres only with the
authorisation of the relevant supervisory authority.
The relevant supervisory authority or the operator of the equipment are
responsible for determining the explosion hazard (zone classification).
The operator must check and ensure that all technical data and the marking of the
equipment in accordance with ATEX are compliant with the necessary requirements.
The operator must provide corresponding safety measures for all applications in
which the breakdown of the equipment might lead to danger to persons.
If any irregularities are observed while the equipment is in operation, the equipment
must be put out of operation immediately and WALTHER Spritz- und Lackiersysteme
List of replacement parts:
PILOT WA 110
V 20 340
Item Description
Qty Article-No.:.
1
Air cap
1
V 20 340 30 033
2
Material nozzle
1
V 20 340 40 033
3
Air cap nut
1
V 20 340 10 000
4
O - Ring
1
V 09 103 03 001
5
Front spray gun section compl.
1
V 20 340 01 000
6
O - Ring
1
V 09 102 08 001
7
Needle spring
1
V 20 340 20 033
8
Piston
1
V 20 340 03 000
9
O - Ring
1
V 09 103 04 001
10
Needle chuck
1
V 10 106 02 000
11
O - Ring
3
V 09 102 20 001
12
Piston spring
1
V 20 340 04 000
13
Threaded bushing
1
V 20 340 05 000
14
Piston housing, compl.
1
V 20 340 02 000
15
Countersunk screw
3
V 20 340 06 000
16
Quick-release fitting
3
V 20 340 09 000
17
Bracket
1
V 20 340 07 000
18
Socket head cap screw
2
V 20 340 08 000
We recommend that bold-face replacement parts (i.e. wear parts) are hold on
stock.
Repair kit
WALTHER supplies a repair kit containing all wearing parts for the automatic spray
gun PILOT WA 110. This parts are shown in
boldface
print in the list of the replace-
ment parts:
Article-No.:
V 16 203 40 . . 3