Wallgate WDC200 Product Manual Download Page 23

Page: 23 / 33

Product Manual WDC200 Electronic Control

Revision 18

Table 6. WDC200 Menu Settings

Main Menu Item

Sub Menu 1

Sub Menu 2

Available
Options

Default
Value

Firmware version number appears. Use ↓ key to view the main menu.

System Settings
Management

Start the System
Test

System Test

Enabled or Disabled

Disabled

Enable or disable
Exclusivity

Exclusivity

Basin Excl.

Enabled or Disabled

Disabled

Shower Excl.
W.C. Excl.

Enable or disable
Water Lockouts

Water Lockouts

Enabled or Disabled

Disabled

Select the operating
mode and defaults

Mode & Defaults

Cell or Communal

Cell

Enable or disable
Cistern Sharing

Cistern Sharing

Enabled or Disabled

Disabled

Enable or disable
the High Voltage
Flush

High Volt Flush

Enabled or Disabled

Disabled

Enable or disable
Double Press Flush

Double Press Flush

Enabled or Disabled

Disabled

Enable or disable
the Shower and
Basin infrared
sensor inputs

I.R. INPUTS

Basin IR Input

Enabled or Disabled

Disabled

Shower IR Input

Enabled or Disabled

Disabled

Specify the Time
and Date

Set Date & Time

Set Time

HH:MM

Set Date

DD/MM/YY

Assign the Remote
Inputs

Remote Input
Setup

Remote Lockout,
Remote Flush, Half
Flush, Not Used,
Purge, clear lockouts,
flow sensor.

Remote Lockout

Remote Flush

Half Flush

Reset the WDC200
settings to Factory
Defaults.

Load Factory
Settings

Refer to the
WDCMS setup
procedure.

Network Address

1 to 30

Lockout Mode

Mode

1 or 2

Summary of Contents for WDC200


































Search results

Summary of Contents for WDC200

Reviews:

Related manuals for WDC200

Brands by name

Popular brands

Wallgate WDC200, Product Manual

Search results

Summary of Contents for WDC200

Reviews:

Related manuals for WDC200

Brands by name

Popular brands