Wallenstein WXR545PL Operator'S Manual Download Page 38

Page: 38 / 42

Specifications

WXR545PL

Trailer Wood Splitter

11.2 Common Bolt Torque Values

Checking Bolt Torque

The tables shown give correct torque values for

various bolts and capscrews. Tighten all bolts to the

torque values specified in the table, unless indicated

otherwise. Check tightness of bolts periodically.

IMPORTANT! If replacing hardware, use

fasteners of the same grade.

IMPORTANT! Torque figures indicated in the

table are for non-greased or non-oiled threads.

Do not grease or oil threads unless indicated

otherwise. When using a thread locker, increase

torque values by 5%.

NOTE:

Bolt grades are identified by their

head markings.

Imperial Bolt Torque Specifi cations

Bolt

Diameter

Torque Value

SAE Gr. 2

SAE Gr. 5

SAE Gr. 8

lbf•ft

N•m

lbf•ft

N•m

lbf•ft

N•m

1/4"

5/16"

3/8"

7/16"

100

1/2"

110

115

155

9/16"

115

155

165

220

5/8"

128

160

215

220

305

3/4"

165

225

290

390

400

540

7/8"

170

230

420

570

650

880

225

345

630

850

970

1320

Metric Bolt Torque Specifi cations

Bolt

Diameter

Torque Value

Gr. 8.8

Gr. 10.9

lbf•ft

N•m

lbf•ft

N•m

0.4

0.5

1.3

1.8

2.2

3.3

4.5

M10

M12

125

M16

166

225

229

310

M20

321

435

450

610

M30

1,103

1 495

1,550

2 100

M36

1,917

2 600

2,700

3 675

Summary of Contents for WXR545PL











































Search results

Summary of Contents for WXR545PL

Reviews:

Related manuals for WXR545PL

Brands by name

Popular brands

Wallenstein WXR545PL, Operator'S Manual

Search results

Summary of Contents for WXR545PL

Reviews:

Related manuals for WXR545PL

Brands by name

Popular brands