Wallenstein WXR545PL Operator'S Manual Download Page 30 | Manualshive

Page: 30 / 42

background image

Transporting

WXR545PL

Trailer Wood Splitter

30

Vertical Splitting

00204

Fig. 25 –

Vertical Splitting

7. Transporting

7.1 Prepare for Transport

•

Make sure the pivoting main frame is fully lowered

to horizontal. The lock pin in the pivoting splitter

beam must be fully engaged.

00206

Fig. 26 –

Lock Pin Fully Engaged

•

Turn the fuel OFF when transporting.

00278

Fig. 27 –

Fuel Valve OFF

•

Clean all debris from the splitter that could fall off in

transport.

•

Check tire pressure. Inspect for cuts or damaged

rims.

•

Check lug nuts and re-torque as necessary.

Inspect again after 20–25 mi (32–40 km). Check

weekly. See

•

Inspect and replace any axle dust caps that are

missing, damaged or leaking.

•

Always be in compliance with all applicable local

regulations when transporting.

«
...
28
29
30
31
32
...
»

Summary of Contents for WXR545PL











































Reviews:

No comments

Related manuals for WXR545PL

Brand: Patton electronics Pages: 16

Brand: Lika Pages: 2

Brand: Boss Audio Systems Pages: 5

Brand: KAMEHA Pages: 12

Brand: Caen Pages: 17

Brand: I.D. AL Pages: 26

Brand: nedis Pages: 28

IFS MC250-4T Series

Brand: Interlogix Pages: 23

Raymarine E22158

Brand: FLIR Pages: 48

Brand: Cobra Pages: 12

Brand: Clarke Pages: 12

Brand: Powerlink Pages: 4

Brand: ADF Web Pages: 36

Brand: Hubner Pages: 48

Brand: Grupo Urrea Pages: 8

A1-Hybrid Series

Brand: SolaX Power Pages: 43

Brand: Nokia Pages: 6

Brand: HP Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands