background image

8

P202

Product Warranty

rev. Nov-2018 

 

LIMITED WARRANTY 

 

 

Wallenstein products are warranted to be free of defects in materials and  

workmanship under normal use and service, for a period of 

Five Years for Consumer Use 

Two Years for Commercial/Rental Use 

from the date of purchase, when operated and maintained in accordance with the opera

ng 

and maintenance instruc

ons supplied with the unit. Warranty is limited to the repair of the 

product and/or replacement of parts. 
This warranty is extended only to the original purchaser and is not transferable.  
Repairs must be done by an authorized dealer. Products will be returned to the dealer at the 

customer’s expense. Include the original purchase receipt with any claim. 

This warranty does not cover the following: 

1)

 

Normal maintenance or adjustments 

2)

 

Normal replacement of wearable and service parts 

3)

 

Consequen

�al

 damage, indirect damage, or loss of pro

ts 

4)

 

Damages resul

ng from: 

 

Misuse, negligence, accident, the

 or 

re 

 

Use of improper or insu

cient fuel, 

uids or lubricants 

 

Use of parts or a

ermarket accessories other than genuine Wallenstein parts 

 

Modi

ca

ons, altera

on, tampering or improper repair performed by par

es other 

than an authorized dealer 

 

Any device or accessories installed by par

es other than an authorized dealer 

5)

 

Engines. Engines are covered by the manufacturer of the engine for the warranty period 

they specify. For the details of your engine warranty, see your engine owner’s manual. 

Informa

on about engine warranty and service is also available in the FAQ sec

on at 

www.wallensteinequipment.com 

 

Summary of Contents for P202











Reviews: