background image

SafeFlame 96 D / 97 D

2

Figure 5: Minimum dimensions of the space required for installation of stove. When installing the stove into a fixed
position, the width and depth measurements of the installation opening are identical to those shown in the oven installation
diagram 495 mm and 530 mm. Figure 4. When installing a gimbal-mounted oven, the width and depth measurements of
the installation opening are identical to those shown in the installation diagram for the stove 510 mm and 550 mm. Figure
5.

Figure 6: The dimensions of the space required for
installation of the 96 D oven’s control panel. Heat will
make electronics life time shorter; It is not recommended
to mount the control panel right above the shutter of the
oven.

Figure 7:

Figure 8:

Figure 9: Installation of the exhaust pipes in a
gimballed stove. Length of the exhaust pipe: to the
right 900 mm and 1500 mm., to the left 1000 mm
and 1200 mm.

Fitting the Appliance into the
Installation Opening

Fixed Installation of the Oven or Stove
1.Fit the back edge of the fastening cleat for the rear

pads 355 mm from the front edge of the installation
opening.

2.Lift the oven into the installation opening so that the

rear pads slide into the grooves on the fastening
cleat.

3.Fit the fastening cleat for the front pads onto the

front edge of the installation opening.

4.Fit the oven with an exhaust pipe, which should follow

the most direct route to the lead-through. The exhaust
pipe are insulated with a second, larger diameter
metal pipe.

3.Attach the gimbal-mounting rockers to the oven or

stove.

4.Use screws to attach the rockers to the gimbal-

mounting frame.

5.For exhaust pipes not to prevent the oven movements

the pipes are formed into a loop behind the oven and
led through the apertures in the frame to the lead-
through. Figure 9.

6.Protect the exhaust pipe with a second, larger

diameter metal pipe.

7.The fuel hose and the wires must allow the unit to

swing freely in all conditions and they must not come
into contact with the exhaust pipe. The play is best
to turn under the oven.

510 mm

550 mm

min. 635 mm

475 mm

475 mm

530 mm

30

26

25

175

056

Gimbal-mounted Installation of the Oven or
Stove
1.Do not fit pads underneath the oven.
2.Fit the gimbal-mounting frame into the installation

opening.

Summary of Contents for SafeFlame 96 D











Reviews: