background image

WALLAS 40D

 

Operator’s Manual and Installation Guide

 

 

15

WARRANTY: 

 

Wallas·Marin Oy (the manufacturer) shall be liable for eventual defects in the raw material or manufacture 
of the products and items sold by the importer for 12 months from the day of sale on the following 
conditions: 
 

1.

 Measures to take in the event of a defect: 

a)

  

Look on the check list on the website (www.wallas.com) to make sure the defect in 

question is not related to use, .i.e. a simple problem not covered by the warranty. 

b)

  

Notification of the defect must be given in writing immediately if possible and no later than 

two months after the appearance of the defect. After the warranty period ends, a referral back to 
a notification at the time of the warranty period is not valid unless the notification was made in 
writing. A valid receipt or another reliable official document of the time of purchase is required for 
the warranty. 

c)

  

For repairs under warranty, the customer takes the product to the place of purchase (the 

seller is responsible for warranty issues) or to an authorized repair shop. Warranty service is not to 
take place outdoors or on a boat. The warranty does not cover costs for the removal and securing 
of the device or for damage caused by the incorrect packing of a device that has been sent for 
repair. 

 

d)

  

The customer must provide the following information in writing for warranty service: 

 

 

• Description of the problem 

 

 

• A description of where and how the device was installed 

 

 

• Product type and serial number 

 

2.

 The warranty is not valid in the following cases when: 

• Components which are not approved by the manufacturer have been added to the device 
and/or if its structure has been modified without the consent of the manufacturer. 

 

• The instructions for installation, operation or maintenance have not been followed. 

 

• Storage or transport has been inappropriate. 
• A problem has resulted from an accident or damage, which Wallas has had no control over 
(force majeure). 
• Problems arise from normal wear and tear. The fan motors of the heaters (and ventilation hood 
assembly (85D+270) have a natural wear limit of 1500 hours. Exceeding this limit within the warranty 
period means the customer is no longer entitled to replace the motors under warranty. 
• The product has suffered from improper handling. unsuitable fuel, low voltage, excess voltage, 
damage due to dirt or water. 

 

• The device has been opened without the explicit permission of the importer 
• Components other than Wallas' spare part components have been used in the repair of the 
device. 

 

3.

 Repairs carried out

 

during the warranty period do not renew or alter the original warranty period. 

 

4.

 Indirect damages arising from a defective product are not covered by this warranty. 

 

5.

 The warranty is only valid for boat products that have been installed in boats and for collage products 

that have been installed in cottages. The warranty does not cover installation in vehicles or other areas. 
 

6.

 To enable us to offer a high standard of service, the seller must keep a buyer register to inform buyers, if 

necessary, of eventual matters concerning the warranty period or technical information, modifications or 
the updating of the device after the warranty period has expired. 
 

7.

 This warranty does not limit rights written down in the consumer protection laws.  When making a 

warranty claim, the customer must provide proof that the maintenance and safety Instructions have been 
thoroughly followed. 
 
This warranty does not apply to defects which have arisen due to carelessness in following installation, 
operation and maintenance instructions.

Summary of Contents for Nautic 40D

















Reviews: