![wallas 88DU Installation, Operation And Service Instructions Download Page 76](http://html1.mh-extra.com/html/wallas/88du/88du_installation-operation-and-service-instructions_3231562076.webp)
88DU
Installation
GB
490070GB
Connection to a separate tank
Cap run-throughs and sinter
fi
lters are used on plastic tanks.
Installation instructions for Tank connection 367215 (accessory)
If the fuel will be taken from a separate tank, you must install a tank connection
367215.
There are two methods to install the tank connection to the stove.
The recommended way is to use the stove’s own fuel hose.
1. Detach the sinter bronze
fi
lter from the tank connection hose and pull the fuel
hose from the cap.
2. Thread the stove’s fuel hose through the connector in the tank cap. This is
easier, if you use, for instance, soapy water to lubricate the hose.
3. Install the
fi
lter at the end of the hose.
4. Install the tank connection in the tank.
This installation method does not involve opening the cooling box of the stove or
the factory connection to the fuel pump.
An alternative way to install the tank connection:
1. Open the cooling case of stove and detach the stove’s standard fuel hose from
the fuel pump.
2. Thread the tank connection hose through the hole in the cooling case lid.
3. Install the tank connection hose by
fi
rst threading the barrel nut to the hose, after
which the support sleeve should be placed inside the hose and the olive at the end
of the hose.
4. Tighten the barrel nut tightly to the fuel pump connector. Keep the parts and the
hose clean and ensure that the connection is tight, because an air leak in the con-
nector will stop the device from functioning.
5. Install the cooling case back to the stove.
5 l
2024
10 l
30 l
130 l
2027
4030
4130
(accessory)
(accessory)
(accessory)
(accessory)
200 x 300 x 130
380 x 195 x 210
590 x 200 x 300
800 x 400 x 600
Volume
length x height x width
Order code
Wallas fuel tanks
Barrel nut
Support sleeve ø 2 mm
Barrel nut
Sinter bronze
fi
lter
Olive ø 5 mm
Cap seal
Protection spiral
Washer
Seal
Screw cap
Bleeding hose
Attach the loose end of the
hose so as to not allow fuel
to spill as the boat tilts.
88DU_GB.indd 14
11.06.2008 10:42:40
- 76 -
Summary of Contents for 88DU
