background image

Installation

Fuel connections

Things to note about the connections

The standard length of the fuel hose is 4 m (max 6 m). Cut the fuel hose to a length 

suitable for installation.

The lift height of the pump should be less than 2 m; preferably 0.5–1 m.

The fuel pipe must always have a filter. 

Country-specific requirements

The standard fuel hose is plastic. Please observe the country-specific require

-

ments with regard to the material for the fuel hose / pipe, the fuel filter and the hose 

clamps. The inner diameter of a new replacement hose must be equal to the inner 

diameter of the plastic hose.

Copper pipe and metal filters are available as accessories.

Fuel feed

If the lift height is outside the recommended 0.5–1 m, the fuel feed must be 

checked and, if necessary, adjusted. The fuel feed must also always be checked, 

if parts of the fuel system, such as the pump or the electronics card, have been 

replaced.

Fuel system adjustments are device specific. We recommend that the adjustment 

be carried out by an authorised service shop.

Tank placement

1.  The fuel tank should always be placed below the base of the device. (The fuel 

surface level must be below the device.) When the fuel level is above the base, 

the solenoid valve 

30017

 must be installed on the tank-side end of the hose.

2.  The fuel tank can be placed in the base housing 

4031

, or outside it, for exam-

ple, in the foundations of the house or a suitable protective box. Protect the 

tank and the fuel hose from direct sunlight.

3.  The fuel hose lead-through must be shielded by a metal cover pipe.

4.  The standard length of the fuel hose is 4 m. It can be extended with a 2 m ex-

tension hose, which gives a total length of 6 m. Connect the hoses with bayo-

net couplings, which are twisted together.

Optimal fuel tank location

TANK

TANK

MAXIMUM

OPTIMUM

Checking / 

adjustment

Checking / 

adjustment

TANK

If the fuel level in the tank is above the device, a solenoid valve 30017 

must be installed in the fuel line immediately after the tank lead-through.

en

26CC / 40CC

D80151

- 48 -

0,5 m

1 m

2 m

490525C

Summary of Contents for 26CC



















Reviews: