background image

English

Français

Español

 

76

6,981,852    

6,933,634 

7,018,181

7,071,429 

D550,327 

D537,839

D553,325 

D550,329 

D550,328 

7,886,876

Other patents pending

U.S. Patent Nos.

Limited Warranty

AIRLESS PAINT SPRAY EQUIPMENT 

This product, manufactured by Wagner Spray Tech 

(Wagner), is warranted to the original retail purchaser against 

defects in material and workmanship for:

 two years from date of purchase.

This warranty does not cover damage resulting from improper 

use, accidents, user’s negligence or normal wear.  This 

warranty does not cover any defects or damages caused by 

service or repair performed by anyone other than a Wagner 

Authorized Service Center.  This warranty does not apply to 

accessories.

WAGNER

 SHALL NOT IN ANY EVENT BE LIABLE FOR 

ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES 

OF ANY KIND, WHETHER FROM BREACH OF THIS 

WARRANTY OR ANY OTHER REASON. 
If any product is defective in material and/or workmanship 

during the applicable warranty period, please call Wagner 

Technical Service at 1-800-880-0993.  

DO NOT RETuRN 

THE PRODuCT TO THE ORIGINAL RETAILER.  Under 

Wagner’s Free Tool Replacement Program, Wagner 

Technical Service will either replace the defective part, or 

refer you to your nearest Authorized Service Center for 

repair.

SOME STATES DO NOT ALLOW LIMITATIONS ON 

HOW LONG AN IMPLIED WARRANTY LASTS OR THE 

EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL 

DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION 

MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, 

AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH 

VARY FROM STATE TO STATE. 

GARANTIE LIMITÉE

MATÉRIEL DE PULVÉRISATION DE PEINTURE SANS AIR

Ce produit, fabriqué par Wagner Spray Tech (Wagner), est 

garanti, au bénéfice de l’acheteur au détail d’origine, contre 

tout vice de matières et toute malfaçon pour : 

deux années à compter de la date d’achat.

La présente garantie ne s’applique pas aux dégâts entraînés 

par une utilisation incorrecte, par la négligence de l’usager 

ou par l’usure normale. La présente garantie ne s’applique 
pas non plus aux défectuosités ou dommages résultant 
de l’entretien ou de la réparation que fait une personne 
quelconque qui ne soit pas membre d’un centre d’entretien 
autorisé pour les produits Wagner. La présente garantie ne 
s’applique pas aux accessoires.

WAGNER NE POURRA EN AUCUN CAS ÊTRE TENUE 
RESPONSABLE DE DOMMAGES-INTÉRÊTS INDIRECTS 

OU CONSÉCUTIFS, QUE CE SOIT POUR UNE RUPTURE 

DE CETTE GARANTIE OU TOUTE AUTRE RAISON.

En cas de défaut de matériau ou de fabrication du produit 

durant la période de garantie applicable, appelez le Service 

technique Wagner au  1-800-880-0993. 

NE RENVOYEz PAS 

LE PRODuIT Au DÉTAILLANT ORIGINAL. Dans le cadre 

du programme de remplacement gratuit d’outils Wagner, le 

Service technique Wagner remplacera la pièce défectueuse 

ou vous indiquera le centre de service agréé le plus proche.
CERTAINES PROVINCES INTERDISENT LES 

RESTRICTIONS SUR LA DURÉE D’UNE GARANTIE 
IMPLICITE OU L’EXCLUSION DES DOMMAGES 

ACCESSOIRES OU INDIRECTS. IL SE PEUT DONC QUE 

LA RESTRICTION ET L’EXCLUSION ÉNONCÉES CI-

DESSUS NE S’APPLIQUENT PAS À VOUS.

LE PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS 

JURIDIQUES SPÉCIFIQUES, ET VOUS AVEz PEUT-

ÊTRE D’AUTRES DROITS, QUI PEUVENT VARIER D’UNE 

PROVINCE À L’AUTRE.

GARANTÍA LIMITADA

EQUIPO DE ATOMIZACIóN DE PINTURA SIN AIRE

Este producto, fabricado por Wagner Spray Tech (Wagner), 

está garantizado ante el comprador original contra defectos 
de materiales y mano de obra durante:

dos años contado a partir de la fecha de compra.

Esta garantía no cubre los daños que sean resultado de un 

uso inapropiado, accidentes, negligencia del usuario o un 

desgaste normal. Esta garantía no cubre ningún defecto o 

daño que haya sido causado por los servicios o reparaciones 

llevadas a cabo por alguien que no sea un técnico del Centro 

de Servicio Autorizado de Wagner. Esta garantía no es válida 

para ningún accesorio.

WAGNER NO SERÁ EN NINGÚN CASO RESPONSABLE 
DE NINGÚN DAÑO INCIDENTAL O DE CONSECUENCIA 

DE NINGUNA CLASE, QUE RESULTE DE VIOLAR ESTA 

GARANTÍA O POR CUALQUIER OTRA RAZÓN.
Si algún producto presenta fallas en los materiales y/o en 

su fabricación durante el periodo de vigencia de la garantía, 

llame al Servicio Técnico de Wagner al 1-800-880-0993. 

NO DEVUELVA EL PRODUCTO A LA TIENDA DONDE 

LO ADquIRIó. Gracias al Programa de Reemplazo de 

Herramientas Gratis de Wagner, el Servicio Técnico de 

Wagner reemplazará la pieza defectuosa o lo derivará 

al Centro de Servicio Autorizado más cercano para su 

reparación.

ALGUNOS ESTADOS NO PERMITEN LIMITACIONES EN 

CUANTO A LA DURACIÓN DE UNA GARANTÍA IMPLÍCITA 

O LA EXCLUSIÓN DE DAÑOS INCIDENTALES O DE 

CONSECUENCIA, DE MANERA QUE LA LIMITACIÓN Y 

EXCLUSIÓN ANTERIORES PODRÍAN NO SER VÁLIDAS 

PARA USTED.

ESTA GARANTÍA LE CONCEDE DERECHOS LEGALES 
ESPECÍFICOS, PERO uSTED PODRÍA TENER DERECHO 

A OTROS, LOS CUALES VARÍAN DE UN ESTADO A 

OTRO.

Summary of Contents for Procoat 9185G





























Reviews: