• Do not use materials with a flashpoint below 21° C (70°
F). Flashpoint is the temperature at which a fluid can
produce enough vapors to ignite.
• Plastic can cause static sparks. Never hang plastic to
enclose spray area. Do not use plastic drop cloths when
spraying flammable materials.
• Use lowest possible pressure to flush equipment.
GAS ENGINE (WHERE APPLICABLE)
Always place sprayer outside of structure in fresh air. Keep all
solvents away from engine exhaust. Never fill fuel tank with a
running or hot engine. Hot surface can ignite spilled fuel.
Always attach ground wire from pump to a grounded object.
Refer to engine owner’s manual for complete safety
information.
HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE
MATERIALS - Will cause severe injury or
property damage.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as
methylene chloride and 1,1,1 - trichloroethane. They are
not compatible with aluminum and may cause an
explosion. If you are unsure of a material’s compatibility
with aluminum, contact your coating's supplier.
HAZARD: HAZARDOUS VAPORS - Paints, solvents,
insecticides, and other materials can be
harmful if inhaled or come in contact with body.
Vapors can cause severe nausea, fainting, or
poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled. Read
all instructions supplied with the mask to be sure it will
provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating
manufacturer.
HAZARD: GENERAL - This product can cause severe
injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• Pulling the trigger causes a recoil force to the hand that is
holding the spray gun. The recoil force of the spray gun is
particularly powerful when the tip has been removed and
a high pressure has been set on the airless pump. When
cleaning without a spray tip, set the pressure control knob
to the lowest pressure.
• Use only manufacturer authorized parts. User assumes
all risks and liabilities when using parts that do not meet
the minimum specifications and safety devices of the
pump manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it
with another earthed high-pressure hose.
• ALWAYS follow the material manufacturer’s instructions
for safe handling of paint and solvents.
• Do not use this unit in workshops that are covered under
the explosion prevention regulations.
• Clean up all material and solvent spills immediately.
• Always unplug cord from outlet before working on
equipment (electric units only).
• Wear ear protection. This unit can produce noise levels
above 85 dB(A).
• Never leave this equipment unattended. Keep away from
children or anyone not familiar with the operation of airless
equipment.
• Do not spray on windy days.
Earthing Instructions
Electric models must be earthed. In the event of an electrical
short circuit, earthing reduces the risk of electric shock by
providing an escape wire for the electric current. This product
is equipped with a cord having an earthing wire with an
appropriate earthing plug. The plug must be plugged into an
outlet that is properly installed and earthed in accordance with
all local codes and ordinances.
DANGER
—
Improper installation of the earthing plug can
result in a risk of electric shock. If repair or replacement
of the cord or plug is necessary, do not connect the green
earthing wire to either flat blade terminal. The wire with
insulation having a green outer surface with or without
yellow stripes is the earthing wire and must be connected
to the earthing pin.
Check with a qualified electrician or serviceman if the earthing
instructions are not completely understood, or if you are in
doubt as to whether the product is properly earthed. Do not
modify the plug provided. If the plug will not fit the outlet, have
the proper outlet installed by a qualified electrician.
General Description
This high performance airless sprayer is a precision power tool
used for spraying many types of materials. Read and follow
this instruction manual carefully for proper operating
instructions, maintenance and safety information.
Specifications
Weight:
Hopper unit ...................17 kg (37 lbs.)
Suction set unit .............20 kg (44 lbs.)
Capacity ...........................Up to 1.25 liters (.35 gallons) per
minute
Power source ...................Electric motor, totally enclosed, fan
cooled
Voltage .............................220–240 VAC, 50/60 Hz, 6.2 A or
100–120 VAC, 50/60 Hz, 11.0 A
Spraying pressure ............Up to 20.7 MPa (3000 PSI)
Capabilities.......................Sprays a variety of oil-based and
latex paints, primers, and stains
Return Tube
PRIME/SPRAY
Valve
Suction Tube
Motor ON/OFF
Switch
Pressure Control
Knob
© Wagner. All rights reserved.
3
GB
R