background image

Technical data 

 

 

05 / 2009 

0351701

  -  PEA-T3XL

 

21

 

6. Technical 

data 

 

Weight: 

PEA-T3XL 1.8:

 

2400 g 

PEA-T3XL 1.4:

 

2100 g 

PEA-T3XL 1.1:

 

1840 g 

PEA-T3XL 0.85: 

1620 g 

 

06_Tribopistolendaten.doc 

Electrical: 

Design: 

as per EN 50177 and EN 50050 

Protection class: 

IP 54 

Pneumatic: 

Input air pressure (Tribo air): 

max. 43.5 psi (3 bar) 

Powder output quantity: 

max. 300 g/min 

 

 

06_ .doc 

Required compressed air quality: 

Quality class 

Compressed air quality according to ISO 8573.1

 

Max. residual water:

(pressure dew point in in °F at 100 psi

/ °C at 700 kPa) 

+44.6 °F / +7 °C 

Max. oil contents: 

0.1 mg oil/m

3

 / 0.1 oz/ft

3

 

Max. concentration: 

5 mg/m

3

 / 5 oz/ft

3

 

Max. particle size: 

μ

m / 5 microns 

Ambient conditions: 

If low temperature powders are used, the ambient temperature may have to be lower than 
86 °F (30 °C). 

 

 

Volume measures: 

For volumes, specified in Nm

3

 (standard cubic meters). One cubic meter of a gas at

32 °F

 (0 °C ) and 1.013 bar is called norm cubic meter. 

1 Nm

3

/h = 35.3 ft

3

/h; 1 bar = 14.504 psi 

 

Summary of Contents for 0351029





































Reviews: