Waeco PerfectView CAM44 Installation And Operating Manual Download Page 16

EN

Notes on the electrical connections

PerfectView CAM44

36

7

Notes on the electrical connections

7.1

Laying cables

A

NOTICE! Risk of damage!

To prevent damage, when drilling ensure that there is sufficient 
space on the other side for the drill head to come out.

Cables and connections which are not properly installed will 
cause malfunctions or damage to components. Correct installa-
tion of cables and connections is the basic prerequisite for last-
ing and trouble-free operation of the retrofitted components.

The cables may not be exposed for long periods to solvents 
such as benzine, as the solvents can damage the cable.

Please therefore observe the following instructions:

As far as possible, use original openings or alternative openings for the 
connecting cable duct, e.g. the paneling edges, ventilation grilles or blank 
panels. If no openings are available, you must drill holes for the cables. 
Check beforehand that there is sufficient room for the drill head to come 
out on the other side.

Wherever possible, lay cables inside the vehicle, as they are better pro-
tected there than outside.
If you do need to lay a cable outside the vehicle, ensure that it is well fas-
tened (use additional cable ties, insulating tape etc.).

To prevent damage to the cables, when laying them, ensure that they are 
far enough away from hot or moving vehicle components (exhaust pipes, 
drive shafts, light systems, fans, heater etc.). Use corrugated piping or 
other protective materials to protect against mechanical wear.

Screw on the plug connections of the connecting cables to protect against 
water penetration (fig.

0

, page 5).

When laying the cables, make sure:
– They are not kinked or twisted
– They do not rub on edges
– They are not laid through sharp-edged ducts without protection 

(fig.

3

, page 4).

Attach the cables securely in the vehicles to prevent tripping hazards. Use 
cable binders, insulating tape or glue the cables in place.

_CAM44.book  Seite 36  Mittwoch, 7. März 2012  10:15 10

Summary of Contents for PerfectView CAM44




























Reviews: