Threadlockers and Sealants
Threadlockers and Sealants
Threadlocking adhesives and sealants are specified throughout this
manual by a notation of “S” plus a number (S#) and should be used
where indicated. Threadlocking compounds normally break down at
temperatures above 175°C (350°F). If a screw or bolt is hard to
remove, heat it using a small propane torch to break down the sealant.
When applying sealants, follow instructions on container. The sealants
listed are recommended for use on Wacker equipment.
TYPE
( ) = Europe
COLOR USAGE
PART NO. –
SIZE
Loctite 222
Hernon 420
Omnifit 1150 (50M)
Purple
Low strength, for locking threads smaller
than 6 mm (1/4”).
Hand tool removable.
Temp. range: -54 to 149°C (-65 to 300°F)
73287 - 10 ml
Loctite 243
Hernon 423
Omnifit 1350 (100M)
Blue
Medium strength, for locking threads
larger than 6 mm (1/4”).
Hand tool removable.
Temp. range: -54 to 149°C (-65 to 300°F)
29311 - .5 ml
17380 - 50 ml
Loctite 271/277
Hernon 427
Omnifit 1550 (220M)
Red
High strength, for all threads up to 25 mm
(1”).
Heat parts before disassembly.
Temp. range: -54 to 149°C (-65 to 300°F)
29312 - .5 ml
26685 - 10 ml
73285 - 50 ml
Loctite 290
Hernon 431
Omnifit 1710 (230LL)
Green
Medium to high strength, for locking
preassembled threads and for sealing
weld porosity (wicking).
Gaps up to 0.13 mm (0.005”)
Temp. range: -54 to 149°C (-65 to 300°F)
28824 - .5 ml
25316 - 10 ml
Loctite 609
Hernon 822
Omnifit 1730 (230L)
Green
Medium strength retaining compound for
slip or press fit of shafts, bearings, gears,
pulleys, etc.
Gaps up to 0.13 mm (0.005”)
Temp. range: -54 to 149°C (-65 to 300°F)
29314 - .5 ml
Loctite 545
Hernon 947
Omnifit 1150 (50M)
Brown
Hydraulic sealant
Temp. range: -54 to 149°C (-65 to 300°F)
79356 - 50 ml
Loctite 592
Hernon 920
Omnifit 790
White
Pipe sealant with Teflon for moderate
pressures.
Temp. range: -54 to 149°C (-65 to 300°F)
26695 - 6 ml
73289 - 50 ml
Loctite 515
Hernon 910
Omnifit 10
Purple
Form-in-place gasket for flexible joints.
Fills gaps up to 1.3 mm (0.05”)
Temp. range: -54 to 149°C (-65 to 300°F)
70735 - 50 ml
Summary of Contents for WM 90
