Wacker Neuson PSA2 500 Operator'S Manual Download Page 50

Perform Maintenance Safely

Ultra-Low Sulfur Diesel (ULSD) Hazard

WARNING! 

Ultra-Low Sulfur Diesel (ULSD) poses a 

greater static ignition hazard than earlier diesel 
formulations with higher sulfur content. Avoid death or 
serious injury from fire or explosion; 

consult with your 

fuel or fuel system supplier to ensure the delivery 
system is in compliance with fueling standards for 
proper grounding and bonding practices.

Engine Coolant Hazards

WARNING!

 Avoid serious injury or death. Liquid 

cooling systems build up pressure as the engine gets 
hot, so 

use extreme caution before removing the 

radiator cap. 

• Stop the engine and wait for the system to cool
• Wear protective clothing and safety glasses
• Turn the radiator cap slowly to the first stop to allow

the pressure to escape before removing completely

Hydraulic System Hazards

Be sure to follow manufacturer’s instructions for relieving 
fluid pressure before performing any maintenance. The 
hydraulic system is pressurized whenever the engine is 
on and may hold pressure even after the engine is shut 
off. Cycle hydraulic controls, including auxiliary hydraulic 
control (if equipped), after the engine is shut off.

During inspection of the hydraulic system:
• Wait for fluid to cool before disconnecting the lines

Hot hydraulic fluid can cause 

severe burns

• Wear appropriate eye protection. Hydraulic fluid can

cause permanent eye injury

• When venting or filling the hydraulic system, loosen

the filler cap slowly and remove it gradually

Never

 reset any relief valve in the hydraulic system

to a pressure higher than recommended by the 
manufacturer

Check for 

leaks and inspect 

hoses

Allow radiator to cool 

before removing cap 

slowly

29

Perform Maintenance Safely

Hydraulic Fluid Injection Hazard

WARNING! 

Accidental injection of high-pressure 

fluid into the hands or body is dangerous and could 
result in death or serious injury. 

Use caution when 

checking hydraulic leaks as pressurized hydraulic 
fluid has enough force to penetrate skin, causing 
serious personal injury. 

If a leak is discovered:
• Ensure engine is turned off; relieve pressure in

hydraulic circuit

• Wear proper hand and eye protection
• Visually examine the hydraulic hoses or fluid lines in

the vicinity of the leak for breaks or cracks. 

Do not

use your hand to check for leaks

• Repair or replace hydraulic lines according to the

manufacturer’s recommendations

Fluid injection injuries are not always obvious. Victims 
have reported such injuries feel like a bee sting or 
splinter under the skin. If you suspect you have a fluid 
injection injury, do not take chances. Seek proper 
medical care immediately. If any fluid is injected into the 
skin, it must be surgically removed within a few hours by 
a doctor familiar with this type of injury.

Wear 

eye protection

High pressure  

fluid can inject  

into the body

30

Summary of Contents for PSA2 500





























































Reviews: