49
Perform Maintenance Safely
Track Maintenance And Adjustment
Check the tracks daily because the stability of the
compact excavator can be dramatically affected by
damage to tracks.
Check for:
— Damage or wear
— Correct tension according to manufacturer’s
instructions
— Proper lubrication of track rollers and idlers—refer to
the manufacturer’s manuals.
Track tension is important for good performance,
reducing excessive track wear and preventing the tracks
from coming off. Track and roller wear varies with
working conditions and soil conditions. Special tools
and procedures may be needed to check or adjust track
tension. Follow manufacturer’s specific service
procedure(s) when removing and installing tracks.
WARNING!
Track tensioning systems have compressed
springs or pressurized fluid (oil or grease). Improperly
releasing track tension forces can result in death or
serious injury.
Always follow the manufacturer’s
warnings and instructions for track adjustment and
other maintenance and servicing procedures.
WARNING!
Avoid possible death or serious injury.
Never strike or pound on track tension springs.
They may be under very high compression and could
shatter explosively.
Check For
Track Damage
Follow
Maintenance
Instructions
50
Perform Maintenance Safely
Complete Service And Repairs Before Machine
Is Released
Tighten all bolts, fittings and connections to torques
specified by the manufacturer.
Clean or replace all damaged, missing or painted-over
signs, plates and decals that cannot be read.
Inspect and install all guards, covers and shields after
servicing. Replace or repair any damaged parts. Refill
and recharge pressure systems only with manufacturer-
approved or recommended fluids.
Check readiness of fire extinguishers, if so equipped.
Do not paint over or otherwise interfere with fire
detectors or fire extinguisher access points.
Follow the instructions in the manufacturer’s manual(s)
for proper service of any fire suppression equipment on
the machine.
Air conditioning service is limited to approved service
personnel. Refer to the manufacturer’s manual(s).
Start the engine and check for leaks. (See page 46,
Hydraulic System Hazards
.) Operate all controls to
make sure the machine is functioning properly. Test
the machine if necessary. After testing, shut down
and check the work you performed. Are there any
missing cotter pins, washers, locknuts, etc.? Recheck
all fluid levels before releasing the compact excavator
for operation.
All parts should be inspected during repair and replaced
if worn, cracked or damaged. Excessively worn or
damaged parts can fail and cause death or injury.
Verify
Service Work
When
Completed
Summary of Contents for ET18
